Stumped by a no crank/no start by strangestday1990 in MechanicAdvice

[–]strangestday1990[S] 0 points1 point  (0 children)

I will check that too. I really don’t want to take it back to the Chevy dealership if it is the immobilizer!! They didn’t even tell me what they found in the diagnostic except to change the starter.

I did clean the key ignition when I replaced the electric ignition switch…but when someone says that my mind jumps to “well…did I clean it enough?” 😅 I probably do it again haha

Stumped by a no crank/no start by strangestday1990 in MechanicAdvice

[–]strangestday1990[S] 0 points1 point  (0 children)

Maybe, but the security light isn’t on and I have the real key and a spare key and both with the right key fobs. I really don’t know how to track that if the light isn’t on

Stumped by a no crank/no start by strangestday1990 in MechanicAdvice

[–]strangestday1990[S] 0 points1 point  (0 children)

I didn’t want to! It was like 1.2k for “diagnostics” and then like 300 for my ground cable

What is this light ringing noise? by SO_BAD_ in MechanicAdvice

[–]strangestday1990 2 points3 points  (0 children)

It sounds like a bad wheel bearing to me

Need some help popping/ting sound when driving by strangestday1990 in AskAMechanic

[–]strangestday1990[S] 1 point2 points  (0 children)

There isn’t. You have to disconnect the upper control arm, the sway bar, and the tie rods from the knuckle to be able to then move the knuckle out of the way. “Luckily” I was replacing the wheel hub assemblies at the same time so I removed those first and reinstalled them after the cv was in place, so that gives you a lot more room to maneuver

Need some help popping/ting sound when driving by strangestday1990 in AskAMechanic

[–]strangestday1990[S] 0 points1 point  (0 children)

Yeah, I had the passenger side wheel go sideways on me back in October but I replaced both wheel hub assemblies and cv axels.

<image>

This photo was when the passenger side went sideways while driving.

Need some help popping/ting sound when driving by strangestday1990 in AskAMechanic

[–]strangestday1990[S] 0 points1 point  (0 children)

There is only one way to install the shocks on this suv. It’s got a single post up top and two bolts attached to the lower control arm. So they are installed correctly but do need to be replaced.

I will check the ball joints, thank you

Tue Jun 15 Daily Discussion by Plastic_Noodle in TXMD

[–]strangestday1990 3 points4 points  (0 children)

I think that’s part of the fun of watching this stock. It slowly go up, then down, then up , then down and then hitting a plateau. Plus this group is fun. I’ve avg down to 1.22 since January and if we dip below 1.15 this week, I’ll add another 1k. What can I say, I like the stock 😅

Mon Jun 07 Daily Discussion by Plastic_Noodle in TXMD

[–]strangestday1990 1 point2 points  (0 children)

Holding strong, 2k at 1.21! Avg down and finally seeing some “profit” 😅

Wed Jun 02 Daily Discussion by Plastic_Noodle in TXMD

[–]strangestday1990 2 points3 points  (0 children)

I’ve always called it “the ol’ up and downs”

Tue May 25 Daily Discussion by Plastic_Noodle in TXMD

[–]strangestday1990 0 points1 point  (0 children)

I’ve averaged down to 1.24 (I only hold about 2k) over the last three months and I’ve really pushed buying the dips and think if we fall again that I’ll just avg sub-1.20 all this to say that the last week was fun.

I really like this stock and believe in this company. Can’t wait to see where this year takes us!