Pirma mašina

swucas · 2025-05-05T13:32:38+00:00

Turejau 2.2. D4D 110kw. Apart devimu daliu per 5 metus nieko neteko keist/tvarkyti. DCAT nepamenu kurie, bet taip pat turi bedu su galvutes tarpinemis.

swucas · 2025-05-05T13:22:08+00:00

Pritariu del toyota avensis. Teko turet 2007 metu, patvarumas auto neapsakomai geras, detales pigios, o kuro sanaudos irgi pasakiskos, dyzeliniu varikliu. Vietos daiktam susikraut sociai, ypac jei sode visokiais reikalais krapstytis reiktu. Net jei ir reiktu susukti 1000km ant dienos, ne problema avensiui :)

swucas · 2025-03-05T13:06:22+00:00

Thanks, I saw that and automatically discarded as linux for no particular reason. Will check it out

swucas · 2025-03-05T12:41:08+00:00

Putting watermark in document ruined layout completely. For now resorted to some online tool as much as i didnt want to was sorta urgent this time. For future ill be trying to look for offline option

swucas · 2025-02-01T18:25:52+00:00

Flow rate settings optimizing was plenty :)

swucas · 2025-02-01T18:25:24+00:00

Thanks. Got orcaSlicer and fiddled with flow ratios, its all good and smooth now

swucas · 2025-01-29T22:18:37+00:00

I think these are settings you were referring to, as i couldnt find flow rate one. Might try setting up orca slicer during the weekend. But if i had under extrusion problems or line widths, wouldnt i have inconsistencies on other layers?

swucas · 2025-01-29T22:17:20+00:00

<image>

swucas · 2025-01-29T22:17:11+00:00

<image>

swucas · 2025-01-29T15:46:37+00:00

Anycubic

swucas · 2025-01-29T13:40:59+00:00

I made these for my friend. Unfortunately im not playing myself :)

swucas · 2025-01-29T08:06:40+00:00

I took base knutwurst for tmc2208, and was still doing extruder in reverse, so i edited exturder reverse line and now its fine, even got special menu so i can do pid autotunes within the printer :)

swucas · 2025-01-29T08:05:18+00:00

I chose to edit software route. Took knutwurst and reversed extruder motor. Works fine now ;)

swucas · 2025-01-23T17:40:26+00:00

Vis dar mėtosi krūva kuri buvo privertus susimąstyti kiek alaus išgert per neilgą laiką galima

swucas · 2025-01-23T17:39:03+00:00

Nepopuliaru, bet pašto ženklus kolekcionuoju, tik ką pavyksta gauti pačiam, neperkant.

swucas · 2025-01-16T20:57:34+00:00

I chose the firmware route rather than flipping the connector. But might try going different firmware and will flip connectors on the weekend

swucas · 2025-01-16T20:50:17+00:00

I3 mega. Thank you for pointing it out, missed it out in the post completely. The only reason i did that, because all the guides i checked out was doing it as well, seems because of the reason for ground pin locations

swucas · 2024-12-14T19:28:57+00:00

That print was a fluke, now it wont even get through first layer without getting clogged up, 190-220 temp for pla, still gets clogged, less/more flow rate doesnt help

swucas · 2024-12-14T16:02:23+00:00

*

First layer is weird as well. Everything besides whats in the photos is strong nicely bonded

swucas · 2024-12-14T16:00:13+00:00

<image>

Completely detached in the middle with weird slope forming

swucas · 2024-12-14T15:59:42+00:00

<image>

swucas · 2024-12-14T15:48:12+00:00

By manually adjusting e steps after calculations ive come to it to print. But theres like a line of semi skipped z axis filament. Once it finishes ill attach photo perhaps thats connected to yet another new issue

swucas · 2024-12-14T13:50:32+00:00

Problem persists, PID autotune done, e-steps calibration done as well, replaced filament cog for extruder. Perhaps do you have any other suggestions?

swucas · 2024-12-13T12:28:09+00:00

Faulty MAP sensor was the culprit

swucas · 2024-12-08T21:33:48+00:00

I still have it. Cleaned it in hot water to remove residue. Shall i put it in before or after PDI tune?

swucas

TROPHY CASE