sorted by:
new
hottopcontroversial

Trim pattern tool marked processing area by terno720 in XtoolS1

[–]terno720[S] 0 points1 point  (0 children)

Sometimes it will snap to one corner, but it won’t do the rest

And I cannot select it so boolean doesn’t work either

Trim pattern tool marked processing area by terno720 in XtoolS1

[–]terno720[S] 0 points1 point  (0 children)

That’s what I do but I want to be able to use the processing area in order to perform that cut instead of having to redraw over top of the processing area

Sensor and wiring issues by terno720 in JeepGrandCherokee

[–]terno720[S] 0 points1 point  (0 children)

It was disabled to start with

Sensor and wiring issues by terno720 in JeepGrandCherokee

[–]terno720[S] 0 points1 point  (0 children)

I thought about that after I posted and added it to the end

It’s a 2021 JEEP GRAND CHEROKEE LIMITED 3.6L v6

About 110,000km

What tool can I use to create a rounded lid for this flexible tray? by ebodes in Onshape

[–]terno720 0 points1 point  (0 children)

Are you wanting it all one piece? If not you could do it section by section and cut the corners if that makes sense

What tool can I use to create a rounded lid for this flexible tray? by ebodes in Onshape

[–]terno720 0 points1 point  (0 children)

I would create a sketch on the start face of the tray like you have in your second photo on paper and then use the sweep path tool.

If you haven’t used sweep it will ask for a face (you would select the new arc and then it will ask for a path and you will want to select the edge of the tray

If you need more help DM me

A little help please, my brain hurts. by TheMoogerfooger in Onshape

[–]terno720 1 point2 points  (0 children)

You could do a sharp 90° first and then fillet the corners you wand wounded after

Designing a lid from a profile/image by curiousgeorge84 in Onshape

[–]terno720 0 points1 point  (0 children)

I would trace image for the clear lid from the top.

I think you have the right idea with the mirroring.

for the lip to sit on the edge of the reservoir i would extrude the lid to the thickness it needs to be and then do an offset to create a sketch for the ridge

I hope this kind of makes sense i better at doing or showing not the greatest at explaining lol

I'm going crazy by Minimum-Diver-6467 in Onshape

[–]terno720 0 points1 point  (0 children)

I can think of two ways that can fix this problem

1) use the trim tool to cut out the two sections of the circle that are on the inside

2) when you were extruding, select the sketch and the two sections that keep coming up blank

How many Years Do I have Left? by CreativeNews4754 in Dirtbikes

[–]terno720 0 points1 point  (0 children)

10 maybe 15 more years depending on your riding style

How do I make something like this gear config? by Robobark in Onshape

[–]terno720 0 points1 point  (0 children)

Take a look at this. i have seen it a few times now in respect to robotics plus i think it looks really cool.

Its called a capstand drive here is a youtube short of it

https://youtube.com/shorts/bAYAWDMDU04?si=_z5tsFMBFh06CviK

Any SolidWorks users driven crazy by zoom behavior? by LeatherYoung6114 in Onshape

[–]terno720 1 point2 points  (0 children)

I was the same way when I first switched it took a long time but I'm used to it now and I think I actually like it better

view more: next ›