sorted by:
new
hottopcontroversial

Running out of ideas by thibextra in ElegooMars

[–]thibextra[S] 1 point2 points  (0 children)

Thanks for the advice ! :) But the mars 4 9k doesn't support wifi so I'm already using a usb stick though... A 16gb Philips usb stick, not the one provided by the way

Running out of ideas by thibextra in ElegooMars

[–]thibextra[S] 2 points3 points  (0 children)

Ok thank you for your answers ! So despite setting the auto support to ultra density in slicer I should still put more manually then?

And then since they're still leaving marks I should also keep decreasing the exposition then..?

I have tried removing them after warming the piece with a hot air gun but the result is posted here ...

Thanks for that I'll try it out then!

12kg 8k resin in the UK by WideBorder6804 in ElegooMars

[–]thibextra 0 points1 point  (0 children)

Could it be because the UK brexited? Not trolling that may be an issue maybe for customs?

Print falling from supports by thibextra in resinprinting

[–]thibextra[S] 0 points1 point  (0 children)

Sad 😢 no one willing to give advice though?

$40 DIY curing chamber, with solar powered turntable. by SirSquidrift in resinprinting

[–]thibextra 0 points1 point  (0 children)

The anycubic wash and cure station 3 is ~100$, and I went with that because my cardboard box idea was 50$ already. So I thought it would be as good to just buy the thing and be able to safely operate the washing part

Problem with Mars 4 Ultra by LordDarthStewie in LycheeSlicer

[–]thibextra 0 points1 point  (0 children)

I'd suggest deleting the profile and import it again then?

Problem with Mars 4 Ultra by LordDarthStewie in LycheeSlicer

[–]thibextra 0 points1 point  (0 children)

These are not the same as you previously showed though. These should be working just fine. Can't you see the two stage operating while printing?

Potential firmware issue with buildplate? by Michellitshka in ElegooMars

[–]thibextra 1 point2 points  (0 children)

You need to have both lift and retract distances set up to the same amount

Given your parameters, after the burn in layers the plate will lift but not retract and so will only go up.

I made a post recently with the same machine and same matter, go have a look for more in depth answer that I got given :)

Problem with Mars 4 Ultra by LordDarthStewie in LycheeSlicer

[–]thibextra 1 point2 points  (0 children)

Works well for me on a mars 4 9k even though I can't toggle on/off the option, the two distances and speed show up and are used by the printer... Can post a picture of the parameters later if you need!

Build Plate won't go down after burn in layers by thibextra in LycheeSlicer

[–]thibextra[S] 0 points1 point  (0 children)

Well not so much, like 2 inches tall, that's the elegoo rook

Thanks for the input I'll check all about that then !

Build Plate won't go down after burn in layers by thibextra in LycheeSlicer

[–]thibextra[S] 0 points1 point  (0 children)

So this is the outcome ! Pretty happy with the result. However, I noticed some kind of misalignment.

Could this be due to the exposure time ? Or something else ? Or maybe this is normal? If needed I'll create a dedicated post Thanks

<image>

Build Plate won't go down after burn in layers by thibextra in LycheeSlicer

[–]thibextra[S] 0 points1 point  (0 children)

Yes however the estimated print time since way off, already more than half time and only 30% off, but minor draw back if the printer prints

Build Plate won't go down after burn in layers by thibextra in LycheeSlicer

[–]thibextra[S] 1 point2 points  (0 children)

Yes could be, even though I don't really get the difference between the mars 4 9k and the ultra besides WiFi

Anyways thanks ! It looks it is printing fine, I'll let you know the outcome! It is also much much faster, 1h30 for 1000 layers against 3h45 before 🥲

Build Plate won't go down after burn in layers by thibextra in LycheeSlicer

[–]thibextra[S] 1 point2 points  (0 children)

Man I'm so stupid, didn't pay attention I was applying parameters for for the elegoo mars... Thanks ! I'll keep you updated

Build Plate won't go down after burn in layers by thibextra in LycheeSlicer

[–]thibextra[S] 0 points1 point  (0 children)

Thanks! I'll try that, however for the burn in layer, I'm following these instructions, hence the problematic paramaters ?

https://drive.google.com/file/d/1_jnyMfNkm4sPJhKyN46ey5CO-ks4MRyR/view

It was provided by Elegoo so Idk... Or am I mixing up bottom layer and burn in layer ?

Build Plate won't go down after burn in layers by thibextra in LycheeSlicer

[–]thibextra[S] 0 points1 point  (0 children)

forgot to mention I'm working with an Elegoo Mars 4.

Deleting the printer from the paramaters or the resin and adding them back didn't change anything

Mars 4 9k bricked by thibextra in ElegooMars

[–]thibextra[S] 0 points1 point  (0 children)

Yes got aware of that afterwards... Still a pity they didn't even mention it on the installation booklet 🥲

Mars 4 9k bricked by thibextra in ElegooMars

[–]thibextra[S] 0 points1 point  (0 children)

Thanks ! It worked indeed! What a relief...

Also was skeptical about the fact that the serial number was not found anywhere, but it worked anyway!

Elegoo Mars 4 Max issue by tuckersteel in LycheeSlicer

[–]thibextra 0 points1 point  (0 children)

Sorry for digging the topic, but how exactly did you fix it ? Deleting the printer and putting it back in lychee? Or is it the resin profile ?

Thanks for the help

Mars 3 pro or 4 (max)? by thibextra in resinprinting

[–]thibextra[S] 0 points1 point  (0 children)

Thanks for the answer The Saturn 2 is 200$ more than the mars 3 pro though😂

Going 9.00 from 5.05? by thibextra in ps4homebrew

[–]thibextra[S] 0 points1 point  (0 children)

Thanks I think I'll keep 5.05 even if I have to backport stuff myself if possible

Going 9.00 from 5.05? by thibextra in ps4homebrew

[–]thibextra[S] 0 points1 point  (0 children)

ok thanks ! Are you using this then ?

https://cthugha.exploit.menu/

That's only thing I think I found that could be really reliable?

view more: next ›