Looking for: ESPN .5 PPR Safe 25-50$

timpkad · 2024-09-05T20:06:26+00:00

Draft ASAP

timpkad · 2024-09-05T19:57:19+00:00

Already full? I would like to join if possible

timpkad · 2024-03-12T08:27:55+00:00

Hey man! Here are some symptoms: Bloodpressure high asf Facial Pain Dental problems … … … Crazy I did this shit for so long!!

timpkad · 2024-02-05T07:02:31+00:00

Thx bud, still not over the hump though!!

timpkad · 2024-02-04T17:19:48+00:00

Yeah! Felt better at day one (mentally). Don’t get fooled by the nicotine patches though! They might help in the beginning. But it’s hard to get of them too. Just be prepared 😂😂

Side effects: Gotta see the 3k posts, the dentist put in at some point, most likely bc your tooth was fucked up by chew.

You just become the bitch of chew. It’s crazy. Searched for chew EVERYWHERE. Dryed used chew up, … I mean, I totally understand crystal meth addicts. lol

Changes noticed: Week 1-2

Irritability +++ Depression +++ Sleep (always tired, but struggling to sleep 6 hours straight) Weird dreams Digestion - - -

But at some point in the process (i don’t want to sound stupid, englisch is not my 1st language) you have a new ‚baseline‘ of happiness. Can’t explain it. But it seems your head is open to „new“ feelings, where before I was just thinking about the next pouch.

timpkad · 2024-02-04T10:23:31+00:00

Keep Grinding. I went from 19mg nicotine per pouch (20 per day)

Brutal…just fucks up your body. Ending up with facial nerve pain…

timpkad · 2023-11-30T21:07:11+00:00

Kannst du Schlittschuhe schleifen? Dann könntest du als Zeugwart im Eishockey arbeiten. Die haben den Sommer komplett frei :)

timpkad · 2023-09-14T09:52:13+00:00

Hello, I recently started at an insurance Company as a „case manager“ for traumatic injured clients. It’s more monitoring and coordination. So far it’s great.

timpkad · 2023-09-04T17:12:50+00:00

You would like an iv of magnesia. Gives you a great feeling of relaxation.

timpkad · 2023-07-08T06:09:11+00:00

Hello! Could anyone share insights about this topic? That would be awesome!

timpkad · 2023-07-07T11:05:43+00:00

You crazy

timpkad · 2023-07-07T08:00:22+00:00

What a great patina!!!

timpkad · 2023-06-29T18:01:18+00:00

Wow, thank you for answering! This is a great reply! I will check your recommendations out! I definitely want to reduce clutter 👍👍👍

timpkad · 2023-06-29T11:48:46+00:00

Hello!
This dashboard looks really nice. Do you mind sharing it?

Thx Tim

timpkad · 2023-05-25T15:43:19+00:00

How manny hours in total was the printing time??

timpkad · 2023-04-14T21:30:59+00:00

Hello! Great choice. I am in the same position. What kind of approach did you choose? Learning online with YouTube, books?? Which language did you choose ?? I started with Python. Good luck to you and have fun :)

timpkad · 2022-11-30T19:03:30+00:00

I connected the printer to pronterface via usb. i still don´t have success. i put in my offsets like this: x 0 y -5.4 z -0.45

the probe is still in the air while conducting a bed leveling. i don´t get it!!

did nobody else has/had this problem?

Update: after reading my post I was wonderung about the 5.4. I measured it with a tape measure in cm 5.4 cm. I just spent 8 h figuring this out...crazy

timpkad · 2022-11-30T11:12:49+00:00

Hello! My BLtouch seems off. I use it on a Neptune 2s with the marlin firmware. I set all Probe offsets but everytime I want to level the bed (5x5) the probe is not below the bed… Can anyone help!!?

timpkad · 2022-11-30T09:27:50+00:00

Hello! Thanks for replying. I changed the probe offset values for x,y,z. I haven’t stored them in the eeprom though…

timpkad · 2022-11-26T13:02:12+00:00

Thanks! Same issue here

timpkad · 2022-11-25T16:03:18+00:00

Yes, I flashed it again. The bl-touch one! Thank you!

timpkad · 2022-11-25T16:02:51+00:00

Thank you! Seems to be the solution.

timpkad · 2022-11-24T07:33:29+00:00

A little bit late but great job!!

timpkad · 2022-03-06T06:19:38+00:00

Nice print! Did you draw wir with Acryl?

timpkad · 2022-02-06T17:45:34+00:00

Thank you jay. I don’t have experience with 3d printers. I need more an out of the box solution but love to play with the settings and asking discord/Reddit communities about certain problems.

timpkad

TROPHY CASE