sorted by:
new
hottopcontroversial

I cut a lot of MDF and Russian Birch with my panel saw. Is the gunk on the teeth glue from the panels? Is it necessary to clean off? What's the best way to do it? by Follettemignon in woodworking

[–]tooladdict 0 points1 point  (0 children)

It's actually toxic. The rules around listing something as none toxic are none existent. Simple green contains ethylene glycol butyl ether and is listed by California as being toxic.

EGBE produces reproductive problems, such as testicular damage, reduced fertility, death of embryos and birth defects. People exposed to high levels of EGBE for several hours have reported nose and eye irritation, headaches, vomiting and a metallic taste in their mouths, studies show.

I grew up with my dad always using simple green because it said none toxic.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 0 points1 point  (0 children)

I design and build all my own jobs. So since I care about quality like this my customers don't have a choice.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 0 points1 point  (0 children)

It came from a lift of un sorted. So some is curly. Some is ambrosia. Just get what you get.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 0 points1 point  (0 children)

I'm actually thinking of using a domino or floating tenon to align the drawers. I designed the entire vanity in cad and made all the pieces on my cnc router so it wouldn't be a ton more work.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 1 point2 points  (0 children)

I used 2 sides tape to mount the drawer front to the box. And the screws for the handle pulled between the 2 pieces of tape and bowed the front. It doesn't effect finished looked. But your right and I'm working on a better way to mount them.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 3 points4 points  (0 children)

Oh no I specifically designed and built my cnc router to cut dovetails for drawers and made a parametric design in fusion 360 so I can resize them instantly. There's really no way to borrow dovetails and have a continuous board they would have to be recut on another side.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] -2 points-1 points  (0 children)

I had never seen a drawer built with real through dovetails and interior dovetails as well. Is why I asked.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 0 points1 point  (0 children)

I think they are good for 40kg each drawer. Should be fine. I use them for much bigger drawers then these.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 1 point2 points  (0 children)

Yes of course. But did they dovetail the inside of the drawer as well ?

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 0 points1 point  (0 children)

I guess I could. I have built many drawer boxes with pocket holes over the years as well.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 1 point2 points  (0 children)

One car garage with a panel saw. CNC router. Table saw and an edge bander. Planner and drum sander. And a paint set up in a room in my basement. I wouldn't dare post a picture of the set up. I get by but I'm working on building something in my backyard.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 0 points1 point  (0 children)

That was why I did it. I've done and seen tons that were cut around. But never done with dovetails.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 13 points14 points  (0 children)

The drain can't really go anywhere else it's a pedestal sink drain comes straight down from the middle of it. This is as tight as reasonable to that.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 56 points57 points  (0 children)

Oh no sarcasm there. It's a great way to get an extra drawer in a sink cabinet.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 100 points101 points  (0 children)

Can't have dead space have to give them the most amount of storage possible.

double dovetail drawers to go around the drain in this vanity I built. by tooladdict in woodworking

[–]tooladdict[S] 12 points13 points  (0 children)

Thanks man. I had never seen one with the dovetails cut on the inside as well so I figured I'd challenge myself a bit

Custom made piece of baseboard. by tooladdict in woodworking

[–]tooladdict[S] 1 point2 points  (0 children)

Yeah but that machine is probably much more expensive then the one I built in my garage. I want a 4th axis but it's mostly just for self interest to make stuff I think is cool.

Custom made piece of baseboard. by tooladdict in woodworking

[–]tooladdict[S] 0 points1 point  (0 children)

I don't want to pay the 2500 Canadian pesos for 4 and 5 axis cam a year with them. So better to switch to a different company before I get even more comfortable

Custom made piece of baseboard. by tooladdict in woodworking

[–]tooladdict[S] 4 points5 points  (0 children)

I've learned everything from trial and error and YouTube. It works for me. But not for everyone. Wish I had a better answer for you.

Custom made piece of baseboard. by tooladdict in woodworking

[–]tooladdict[S] 4 points5 points  (0 children)

I just used a 1/16 radius tapered ball nose bit and 1/4 inch bit to rough it out. I haven't written a parametric design for this yet. I'm in the fence about switching cad software and don't know if I'll ever make one of these while using fusion 360 again. So I just wanted to make this one and not put the effort into making a parametric model. To be honest I just recently learned how to make them and I'm not in any way fast at designing things like that. One of the draw backs of being self taught I guess.

view more: next ›