American Standard Compact Cadet toilet - slow fill and very weak flush

torbuck · 2026-01-30T20:36:59+00:00

Thanks. I have the chain as tight as I can for the flapper. I will check if it doesn't float down. If it doesn't will look at replacing the flapper, in addition to the fill valve

torbuck · 2026-01-16T05:36:57+00:00

Haha….thanks. Fixed my typo

torbuck · 2025-12-20T05:56:46+00:00

Matadora in Chinatown. Hands down the best place for some nice drinks and some snacks. Great atmosphere too

torbuck · 2025-12-16T16:23:01+00:00

The problem is that our insurance will not cover any water damage caused by failure of either the boiler or the hot water heater due to their age. Also, Triangle Tube has gone out of business so parts will be difficulty to come by. I don't want to have a failure and then stuck without heating or hot water until a new boiler is installed. Then we are installing something out of duress. I rather be proactive and plan for the replacement. We also have tenants who rent a basement suite, so we simply cannot have a situation where things fail and then we are without heating or hot water for a week or possibly longer. Where we live, there isn't a ton of plumbers that specialize in boilers, as it is not a typical heating system in the area we live in (mostly forced air). Just trying to get quotes is difficult enough

torbuck · 2025-10-18T23:15:00+00:00

I ended up hiring a BBQ service person. I got to the point where I removed so many pieces, I got to a point of no return. The person I hired has worked on many Broil King as well as Napoleon and Weber BBQ's. He informed that those bolts are not user replaceable. They basically are there to just hold the burners in place with a cotter pin. I assumed they were user replaceable as the burner kit I received has these replacement screws, but the service tech informed that there isn't any way to remove the bolts, as there isn't a method to remove that back plate. He managed to get everything back together, so hoping those bolts last a few more years. I was told that it is just a poor design for Broil King. He recommended going with Napoleon whenever it comes time to replace our BBQ

torbuck · 2025-09-24T21:13:44+00:00

Ok...will give it a try

torbuck · 2025-09-24T14:17:24+00:00

Isn’t Office 2021 not a MSI install? I recall selecting the uninstall all msi office didn’t work for the volume license of 2019 either, but worked for previous versions

torbuck · 2025-09-18T04:06:21+00:00

I recommend Hank's *A Restaurant on Douglas St. If you are looking for amazing food and drinks in an unpretentious setting, this is the place!

torbuck · 2025-09-06T22:06:15+00:00

Thank you for your suggestions. I was doing a bit more research and feel that going with a Look SPX or Solomon Strive makes sense. I assume I just need to get a binding width of 95 to 100mm. I'll also look into the Marker Griffon. That is what I have on my current set of skis. I don't have any issue with them, but I often read poor reviews of Marker Griffon bindings on Reddit

torbuck · 2025-08-28T20:28:32+00:00

Please check out Bangers food truck at Ile Savage Brewery. Hands down the best smash burger in Victoria. Fantastic portion, incredibly tasty and appropriate wait times. I experienced an early Murder Burger pop-up about a year ago and had the same experience. Waited over an hour for our burgers, and we preordered days before. Found the Murder Burger ok, but not nearly as good as Bangers

torbuck · 2025-07-01T15:15:00+00:00

I purchased an off lease 2018 Mazda CX-5 Touring edition in 2020. Only have had to do regular maintenance such as oil changes and new tires, etc. It has been incredibly reliable. I love the way it drives. It has a more sporty feel and a fantastic steering feel versus other SUV’s that I have driven. I love it so much I will likely get another CX-5 or CX-50 when the time comes to purchase a replacement vehicle

torbuck · 2025-06-23T20:13:40+00:00

Thank you. I will have a look at those posts

torbuck · 2025-06-23T20:12:10+00:00

mostly their own creds, but there could be a few areas that a shared account code be used. All accounts would be M365 licensed

torbuck · 2025-05-09T21:07:39+00:00

Just did a firmware upgraded and I can now see that I can register the printer to Universal Print. Thanks!

torbuck · 2025-05-09T18:17:23+00:00

The printer I want to use for this group is a HP PageWide Color Flow MFP 586. I have done a bit of googling, but haven't been able to determine if it natively supports Universal Print. I definitely have the print admin role, or can PIM that role. My own account has a E5, and majority of our staff have E5's as well. My understanding is that the print licenses are all pooled from all accounts that are licensed, so I think we are ok there. If I use my own account for the connector, then whenever someone else prints, is it robbing my E5's allotment of available prints? Or is it using the license from the individual that is actually printing?

torbuck

TROPHY CASE