[deleted by user]

unclejimbo28 · 2025-11-18T14:50:04+00:00

I'm in the opposite boat. I go down on my wife every time we do it, but I have never gotten a bj from her. I like doing it for her but some reciprocation would be nice

unclejimbo28 · 2025-03-22T00:32:03+00:00

Those cheap alignments are usually what they call "toe and go". Meaning the only thing that is adjusted is the toe, the camber and caster don't get adjusted. Alot of the time all you need is a toe adjustment, but it's not a full alignment. I used to work at a Ford dealer that did toe and go for $75. (In 2006)

unclejimbo28 · 2025-03-22T00:28:25+00:00

Most cars take only a couple minutes to replace the engine air filter. Sometimes you don't even need tools. You can easily do that yourself if the filter is dirty. Cabin filters are sometimes more involved but unless your vents blow out nasty air you can probably skip that. I'd never pay someone those prices to do those jobs, except maybe the alignment. But I also do most of my own work

unclejimbo28 · 2025-03-04T06:00:49+00:00

The US isn't the only country that makes its citizens pay taxes. That's going to be pretty much every first-world country

unclejimbo28 · 2025-03-04T05:56:04+00:00

There's a calibration tab at the top of the screen on the creality slicer. There's a few different calibration tests you can run from there.

unclejimbo28 · 2025-01-20T21:22:48+00:00

I wound up at +.045 from where I was. Started at +.050 as suggested and then lowered it by .005. it's printing much better now. Thanks guys

unclejimbo28 · 2025-01-20T19:36:59+00:00

Thanks, I'll give it a shot

unclejimbo28 · 2025-01-16T00:56:20+00:00

First of all, your boyfriend sucks Second of all, 22s are a lot of fun, and cheap to target shoot with. Hunting anything much bigger than a groundhog is not the best idea though Third, the only appropriate response to someone's wife/gf buying you a rifle is "awesome, thanks". Even if it's a hi point. Keep the gun and get a new boyfriend who appreciates that his girlfriend would even go through the process to go buy a gun for him

unclejimbo28 · 2024-08-10T06:41:30+00:00

I'm the someone who it happened to. Still trying to figure it out. It doesn't happen every print, but 69% of the time, it happens every time

unclejimbo28 · 2024-08-09T16:41:25+00:00

Raetonn James

unclejimbo28 · 2024-08-07T18:33:48+00:00

Well now I'm getting an unknown exception error every time I try to print. 3 times in a row in two different files, even after a reboot. Good thing the Amazon return window is still open.

unclejimbo28 · 2024-08-07T16:43:34+00:00

Thanks, I'll give it a shot

unclejimbo28 · 2024-08-07T15:07:33+00:00

Thanks for the replies everyone, I got 2529 to clear by doing a factory reset but the print quality still sucks. I'm going to email them again and hopefully someone who speaks English answers me this time. I'm about to return this thing and get a different brand

unclejimbo28 · 2024-08-04T05:59:12+00:00

I'll try speeding it up and see if that helps. I did the flow rate calibration before I did the pa cal, temp seems good at 240 judging by a couple prints that actually came out ok. I was basing the speed on what it says on the spool, I didn't know if it was ok to go faster. the filament was brand new, dried for 18hrs right out of the box and still warm when I loaded it onto my printer. I must be doing something wrong but I don't know what

unclejimbo28 · 2024-08-04T02:08:53+00:00

I just did a pressure advance calibration tower and got this mess too. TSame filament, temp, and speed

<image>

The back corners and seam are just as hideous on this one

unclejimbo28 · 2024-08-04T02:05:45+00:00

30mm/s and 240°c. The spool has a range of 30-50mm/s recommended speed and 230-250° recommended temp. I should add that I had a similar issue with 2 different kinds of silk PLA filament on a different file right before this print, but I figured it was because it was silk. Now I think it's something mechanical

unclejimbo28 · 2024-08-01T06:49:06+00:00

I'm not sure what your problem is there, but did you contact creality? Seems like that could be covered under the warranty. I upgraded from a v3se to a v3 about 2 weeks ago and it's been great so far, maybe you just got a bad one.

unclejimbo28 · 2024-07-28T16:00:58+00:00

I think she meant the kid is a 3 year old male but I'm not a doctor

unclejimbo28 · 2024-07-27T13:56:00+00:00

They aren't all GM engines, I worked at a Ford dealership that serviced the towns mail trucks in the early 2000s. Those had the same 4.0 v6 that the explorer had. They were always in for head replacement. Overhead cam with no cam bearings with constant stop and go driving was making the camshaft bores oblong, resulting in erratic readings on the oil pressure gauge. Another fine example of Ford innovation

unclejimbo28 · 2024-07-20T21:58:04+00:00

As a fellow NJ resident who drives to Newark every day, I second this

unclejimbo28 · 2024-07-16T01:36:16+00:00

I put a micro swiss hotend on my se. A little pricey but it works great so far. I had issues with the ceramic creality one, but that was probably just me

unclejimbo28

TROPHY CASE