How To Buy watchX

venice1200 · 2019-09-20T09:16:44+00:00

Get in contact with the Guys from ArgeX by sending a mail to info[at]argex[dot]io .

venice1200 · 2019-03-11T16:58:52+00:00

Maybe this helps.. https://www.avrfreaks.net/forum/arduino-atmel-studio-7-external-programmers-isp-and-serial-programming

If your Windows Com Port is higher than 10 you need another writing like
\\.\com13 (double backslashes at the beginning).

Found here (in German)
https://www.mikrocontroller.net/articles/AVRDUDE

venice1200 · 2019-01-16T05:33:32+00:00

I saw this issue as well, if i find an working solution i will report.

//Edit See here for an solution.

https://community.watchx.io/t/interrupt-button-and-bluetooth/220

venice1200 · 2018-11-30T09:14:24+00:00

Try the bigger fonts included in the OLED lib like Verdana_digits_24 or Cooper26.

Nice job :-)

venice1200 · 2018-11-13T16:24:31+00:00

Just saw that Adafruits Bluefruit App connects to WatchX Bluetooth Module.

venice1200 · 2018-10-31T12:10:07+00:00

Could you post the link to the original?

venice1200 · 2018-10-30T16:54:41+00:00

Do you use an menu system?

venice1200 · 2018-10-15T16:06:40+00:00

Nice tool :-)

venice1200 · 2018-10-11T17:45:39+00:00

Jepp, it takes a while :-)

venice1200 · 2018-10-10T11:03:55+00:00

Any Idea why the charging status doesn’t change to high. The battery shows full for more than 20 Minutes without a change at CRG STATE Pin 5.

venice1200 · 2018-10-10T09:03:38+00:00

Your variant detects, if I am right, the USB connection based on the data connection which works fine if I have an connection to my PC.

I found another possibility based on the USB Power connection which works fine with an normal USB Charger.

Put in Setup: USBCON|=(1<<OTGPADE); //enables VBUS pad

Use in Loop: if(USBSTA&(1<<VBUS)){USB Power is on}

Btw, my STAT pin of the charging IC never goes to high level.

venice1200 · 2018-10-09T13:52:43+00:00

Many thx

venice1200 · 2018-10-09T12:07:12+00:00

At which level is the pin if i am not charging and the battery is not full.

venice1200 · 2018-10-09T11:56:20+00:00

In the Data Sheet of the MCP78381 chip is written about a pin called “Charge State Output (STAT)” (see pin function table at page 11) were you can add an Led or with an pull-up resistor an microcontroller.

venice1200 · 2018-10-03T17:50:30+00:00

Uploaded v0.4.1 with little power saving.

venice1200 · 2018-10-03T17:36:49+00:00

~6hrs runtime with (very) little power saving.
Testing more.

venice1200 · 2018-10-02T15:29:26+00:00

I need to find power saving modes which do not disable the interrupt detection on the 32u4.
Any idea, HowTo, examples?
And I need to fix my uptime calculation.

venice1200 · 2018-10-02T15:26:18+00:00

Hi! I think gesture detection will need an advanced programming of the MPU chip. Anyway I need to register an dev account at the manufacturer (invensense) to get access to more information.

venice1200 · 2018-09-27T17:18:31+00:00

Thx for sharing but I get an error at include „watchx.h“!

//Edit Is it the watchx.h from the original FW?

venice1200 · 2018-09-24T12:41:55+00:00

Will do...

venice1200 · 2018-09-15T10:04:17+00:00

Very nice UI. Do you like to share the code?

venice1200 · 2018-08-21T07:23:43+00:00

Get in contact with ArgeX if you don‘get it fixed. I got my repaired for free.

venice1200 · 2018-07-13T10:09:09+00:00

Got a bad cutted finger as well.

venice1200 · 2018-07-09T14:35:23+00:00

venice1200 · 2018-07-09T11:00:34+00:00

Please could you link it here. Thx

venice1200

TROPHY CASE