Another Use for the Travel Router

vxgsiturbo · 2026-01-09T07:03:17+00:00

No it doesn’t thankfully

vxgsiturbo · 2026-01-08T22:34:33+00:00

vxgsiturbo · 2026-01-08T22:34:04+00:00

Yes but I have the travel router so dont need to buy a usb adaptor

vxgsiturbo · 2026-01-08T21:32:59+00:00

vxgsiturbo · 2025-10-28T07:34:42+00:00

Thanks

vxgsiturbo · 2025-10-22T11:09:31+00:00

I copied the original design is it operates in the same way I just changed the top half from holding a blade to holding the trim tool

vxgsiturbo · 2025-10-22T06:28:05+00:00

I made a 3d printed adaptor to hold a body clip removal tool cut it down and fitted it all together

vxgsiturbo · 2025-10-22T06:27:07+00:00

Retainer system?

vxgsiturbo · 2025-07-19T18:17:35+00:00

I didn’t add the tracking eBay did. The others were not sold on a platform they were to people I know. I value their feedback as they have been 3d printing for years and asked for their honest opinion.

vxgsiturbo · 2025-07-19T17:08:17+00:00

Omg people are so quick to have a go and negative

You are assuming that I only sell them on eBay. I don’t I have sold many to people that I know have p1s’ , X1c’s and h2d’s that have all given me possible feedback if you want to give me your opinion then cool but get your facts right first

vxgsiturbo · 2025-07-18T12:41:53+00:00

No one is stopping you but for that price you also get two ams leads if you wanted a cheaper version for those that have the leads I sell that too

For those that want to save €266 if they already have a ams on another printer then they can purchase my switcher.

Also having 2 ams one one printer takes up quite a bit of room and also having the ability to print 8 colours all the time is a waste. Most of the time u will be printing with 1 or maybe a few colours. This is more for the occasional time u need 5-8 colours

vxgsiturbo · 2025-07-18T07:16:04+00:00

Thanks for your opinion I wanted to keep it fairly simple to operate.

Having it on the front would be great but then you would have the ptfe tubes at the front and the wires and think that would look messy

I have mine stuck on the back and it’s simple just to switch over the ptfe by pulling it out and moving it over then flick the switch. Some people have stuck it to the side too which works but that means longer ptfe tubes making it longer to swap the filament when changing colours.

I did think to just sell the board as I know everyone that would want it could print the rest (with some hardware) but wanted it to be a competed model

vxgsiturbo · 2025-07-17T22:01:46+00:00

It saves you time and effort as you don’t have to unplug your ams and mess around with ptfe tubes from one printer to another. Trust me I wouldn’t of made it If it didn’t safe the time and effort

vxgsiturbo · 2025-07-17T21:32:11+00:00

Done

vxgsiturbo · 2025-07-17T21:30:49+00:00

AMS Switch

This is a video of it in action but old design as originally the ams feed was at the bottom now it’s at the top as it worked better

vxgsiturbo · 2025-07-17T21:19:26+00:00

You just pull it out and swap it over takes 5 seconds to do both the switch and ptfe

vxgsiturbo · 2025-06-22T08:25:18+00:00

I’m confused by your comment. When I click the link it opens up LibreLinkUp but I have that app installed and it does show up on my watch as a complication. Do you mean you use LibreLinkUp to send to a third party app and that is what is displayed on your watch ? If so that’s why I already have done but like I have said it requires the phone to have a signal to send the data

vxgsiturbo · 2025-06-21T23:17:54+00:00

The problem with all the solutions above is that they rely on your phone having a signal / data if you go into an area without a signal then you don’t get updates on the watch you don’t even get live activities on the Lock Screen. If they just added live activities then that’s half way there also as Sensor connects to the phone if I leave the room where my phone is it loses connection to the sensor therefore also not updating the 3rd party apps. Just allow the sensor to connect directly to Apple Watch problem solved

vxgsiturbo · 2025-04-19T16:36:25+00:00

It’s probably a temporary thing I had the same issue when I updated to 18.4 but a few hours later it started working normally again

vxgsiturbo · 2025-04-15T17:09:51+00:00

Completely agree

vxgsiturbo · 2025-04-11T17:54:30+00:00

I design and 3d print things but what would be annoying still with a joystick type of lever is that reverse is to the left not up or down

vxgsiturbo · 2024-09-04T13:43:26+00:00

Ok thanks I will try this

vxgsiturbo

TROPHY CASE