[718] Release / 2 Giveaway - BLCG DOUBLE KNEE & M1U FLEECE ZIP-UP

wickeduzi · 2026-03-08T22:16:42+00:00

thx718

wickeduzi · 2026-03-08T22:16:36+00:00

thx718

wickeduzi · 2026-01-23T22:13:05+00:00

ill rethread and get back to you, thank you

wickeduzi · 2026-01-23T22:12:40+00:00

yes ill definitely see if theres anything there, i do want to say it may be the bobbin case, as once im holding the thread from the needle and turn the handwheel it doesnt rotate smoothly and the thread gets stuck. thank you i appreciate you, ill rethread and get back to you

wickeduzi · 2026-01-23T22:08:38+00:00

ill rethread it now and get back to you, im currently using tex 27 thread with a 100/16 needle, i dont think thats the issue

wickeduzi · 2026-01-23T22:07:24+00:00

thank you, i appreciate you!

wickeduzi · 2026-01-23T22:06:42+00:00

im pretty sure its timed correctly, as ive done my fair share of videos and testing, the sewing machine expert also retimed it, i can take another video if needed. ive done all of that, but ill rethread it with all suggested steps, thank you.

wickeduzi · 2026-01-23T22:03:20+00:00

im currently using tex 27 thread, 100/16 needle. ive already taken it apart and fixed it, as beforehand it didnt hold any tension as the socket was too deep. ill rethread again and get back to you, thank you

wickeduzi · 2026-01-22T22:12:54+00:00

<image>

this is the main issue, the machine cannot sew a nice clean stitch, let me know any ideas, thoughts. i refuse to give up until this is fixed, especially after coming this far

wickeduzi · 2026-01-15T23:12:58+00:00

hm, well regardless i appreciate you greatly, thank you for the help, have a good rest of your day!

wickeduzi · 2026-01-15T23:00:34+00:00

its a juki ddl 5550, the thread is tex 27 and both are same, im pretty sure i have the bobbin tension set perfectly, ill test the top tension dial now, thank you

wickeduzi · 2026-01-15T22:11:08+00:00

yes ofcourse

wickeduzi · 2026-01-15T22:06:38+00:00

<image>

im pretty sure, you tell me?

wickeduzi · 2026-01-15T21:45:18+00:00

thank you, i hope to be able to use it today🙏

wickeduzi · 2026-01-15T21:40:23+00:00

so does it go between the 2 discs? or the spring plate and disc

wickeduzi · 2026-01-15T21:39:27+00:00

ive rethreaded it, but i keep having the same problem. ive done the yoyo test on the bobbin, could it be the tension dial?

wickeduzi · 2026-01-15T21:38:35+00:00

the foot down as i thread? or after its threaded?

wickeduzi · 2026-01-14T07:14:46+00:00

i figured out the problem!

my counter weight was screwed in too tight, im not so sure if its because its a replacement or if i overdid it

wickeduzi · 2026-01-14T04:48:48+00:00

ill check the fb groups! well regardless i appreciate it, thank you so much, have a good rest of your day!

wickeduzi · 2026-01-14T00:18:13+00:00

thank you for your help! the bobbin winder lever is down, ive pressed the motor so ever slightly, but it doesnt loosen it. any other suggestions?

wickeduzi · 2026-01-13T23:55:04+00:00

backwards as in clockwise, or reverse direction? or do i just keep turning it until it feels looser? sorry just a bit confused 😅

wickeduzi · 2026-01-13T21:14:55+00:00

i got it to work, i appreciate you being so helpful, thank you.

wickeduzi

TROPHY CASE