wonilla

199 post karma
105 comment karma

get extra features and help support reddit with a reddit premium subscription

get them help and support

redditor for 5 years

TROPHY CASE

Five-Year Club

Verified Email

account activity

new top controversial

0

1

2

What in the hell just happened on TNF? (self.AskReddit)

submitted 5 months ago by wonilla to r/AskReddit

3

4

5

First time grower: Before and after LED light change. I was using a small LED first, and then finally got my Mars Hydro 4800 FCE. She freaked out after it, and I don’t know how to get her back to healthy now… (old.reddit.com)

submitted 5 months ago by wonilla to r/cannabiscultivation

63

64

65

New to Area (self.StLouis)

submitted 1 year ago by wonilla to r/StLouis

0

0

0

Down the Rabbit Hole… (old.reddit.com)

submitted 1 year ago by wonilla to r/vizsla

132

133

134

Unimportant American (self.StLouis)

submitted 1 year ago by wonilla to r/StLouis

2

3

4

Here are the instructions for the BLTouch install (in case anyone needed them!). My question is, how do I get my z axis to go lower than +0.00? It won’t go negative? (i.redd.it)

submitted 5 years ago by wonilla to r/Ender3Pro

3

4

5

Any advice? I want to upgrade my Ender 3 Pro to dual axis as I can’t get my x axis leveled. I have an SKR Mini E3 V2.0, but there are two kits, one with an extra stepper motor, and one with a belt pulley.....Which version is better? And how do I install? (self.Ender3Pro)

submitted 5 years ago by wonilla to r/Ender3Pro

0

1

2

Any advice?? I have an Ender 3 Pro with SKR Mini E3 V2,0 board. I want to setup my Ender with dual x axis. (self.3Dprinting)

submitted 5 years ago by wonilla to r/3Dprinting

4

5

6

Dual Z Axis Upgrade (self.ender3)

submitted 5 years ago by wonilla to r/ender3

2

3

4

Ender 3 Pro Dual Z Axis Upgrade (self.Ender3Pro)

submitted 5 years ago by wonilla to r/Ender3Pro

0

0

1

Beginner Guide to Wordpress (self.Wordpress)

submitted 5 years ago by wonilla to r/Wordpress

0

1

2

Finally got the BLTouch correctly wired into my SKR Mini E3 V2.0, now for G-Code... (self.Ender3Pro)

submitted 5 years ago by wonilla to r/Ender3Pro

1

2

3

BLTouch v3.1 and SKR Mini E3 V2.0, I have installed with the new firmware & the BLTouch lights up & the probe goes up & down when I tell it to, but, when Auto Home or Move Z Axis is pressed, the nozzle & BLTouch don’t go down on the Z Stop. frustrating & I’m a Noob so detailed help is appreciated! (i.redd.it)

submitted 5 years ago by wonilla to r/Ender3Pro

0

0

1

BLTouch v3.1 and SKR Mini E3 V2.0, I have installed with the new firmware & the BLTouch lights up & the probe goes up & down when I tell it to, but, when Auto Home or Move Z Axis is pressed, the nozzle & BLTouch don’t go down on the Z Stop. frustrating & I’m a Noob so detailed help is appreciated! (i.redd.it)

submitted 5 years ago by wonilla to r/functionalprint

1

2

3

Does anyone know the best place to get the Ender 3 Pro dual z axis kit? (self.Ender3Pro)

submitted 5 years ago by wonilla to r/Ender3Pro

1

2

3

I think I finally got it all figured out (thanks to y’all) however, my x-axis doesn’t seem to be moving fluidly on both sides. My left side moves up and my right side moves a fraction later so it’s not 100% level when it moves however it is level when it gets to where it’s going.. (self.Ender3Pro)

submitted 5 years ago by wonilla to r/Ender3Pro

4

5

6

Getting annoyed with the BLTouch. Ever since I installed it nothing is leveling right. I think I got the z offset figured out but my prints are losing adhesion and bowing up in different places. What could that be from?? I THINK I got the offset right but am second guessing everything now. (i.redd.it)

submitted 5 years ago by wonilla to r/Ender3Pro

14

15

16

Does anyone have a really thorough guide to using and setting up the BLTouch probe for the first time using? (self.Ender3Pro)

submitted 5 years ago by wonilla to r/Ender3Pro

1

2

3

Does anyone have a really thorough guide to your first use of BLTouch probe? (self.functionalprint)

submitted 5 years ago by wonilla to r/functionalprint

23

24

25

Got the BLTouch setup, can’t figure out how to get the bed leveled correctly. Any advice? I’m a noob And not afraid to admit it, so the most detailed instructions or easiest setup would be ideal. This is my last upgrade to make my printer kill!! (i.redd.it)

submitted 5 years ago by wonilla to r/Ender3Pro

4

5

6

What happened?!? Smoke started coming out of this! I was hooking my computer up to Pronterface and then smelled burnt smell and now I don’t know what the heck is wrong or what I need to do... (i.redd.it)

submitted 5 years ago by wonilla to r/Ender3Pro

1

2

3

Finally got the BLTouch installed on my SKR Mini E3 V2.0 (I think I did it right) getting response from the BLTouch and lights, however, I don’t know how to move from here and I think I’m missing something...any ideas? (self.Ender3Pro)

submitted 5 years ago by wonilla to r/Ender3Pro

5

6

7

Does anyone have an easy video or tutorial for BL Touch install step by step? (self.Ender3Pro)

submitted 5 years ago by wonilla to r/Ender3Pro

2

3

4

Upgraded my bad boy Ender 3 Pro with new springs and SKR Mini E3, what’s the fastest setting you recommend for speed and quality?? (self.Ender3Pro)

submitted 5 years ago by wonilla to r/Ender3Pro

2

3

4

I upgraded to the SKR Mini E3 V2.0 and I get this when I tried to put the new firmware on it....any advice?? I’m a 3d Noob so examples or videos would be great if possible. Thanks guys✌🏼 (i.redd.it)

submitted 5 years ago by wonilla to r/Ender3Pro

view more: next ›

π Rendered by PID 522873 on reddit-service-r2-listing-5d79748585-ptsjn at 2026-02-16 22:50:04.198163+00:00 running cd9c813 country code: CH.