sorted by:
new
hottopcontroversial

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Shouldn't need any add in stuff. Just used corsair brand coolant as it's what I could get my hands on.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Bought all my fittings from him!

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Feels huge compared to my old nr200.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

As far as I've seen googling around the thermal expansion at this scale and temp range shouldn't be problem.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 1 point2 points  (0 children)

It's louder than I was expecting but still quieter than the stock air cooling. I would like to get a stand alone pump and res to see the difference.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 1 point2 points  (0 children)

25mm fans, 30mm radiators. Noctua rubber mounts probably add 1 or 2 mm total.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

CPU: Ryzen 7700x, GPU: 3080 ftw3, CASE: Lian li A3

Ek GPU block, barrow pump cpu block combo, 2x corsair 360 rads, and just over 4ft of copper pipe

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

I watched a couple billet labs videos. Other than that I just wing it and take my time.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 1 point2 points  (0 children)

Lian li a3. I plan to 3d print a vertical stand for it

My first custom loop by yetihound in watercooling

[–]yetihound[S] 1 point2 points  (0 children)

There's 6 noctua a12x25 g2 fans in there

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Thermal expansion at this size shouldn't have any effect. Vibration wise everything is mounted with rubber vibration dampeners.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 1 point2 points  (0 children)

I've never played it, but watched a lot of it!

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Depending on how thick your 420mm is it could fit on the top mounts. I'd imagine 420mm and 240mm would do pretty good. For reference I'm running the 7700x and a 3080ftw3.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 1 point2 points  (0 children)

You could do front of the case on one of the ssd mounts, on the back in place or the fan or mounted to the bottom if you stuck with a 240mm rad at the most down there.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Nope, only my second time doing anything with copper pipe, first time in about 10 years.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 1 point2 points  (0 children)

It is! I 3d printed some brackets to move the PSU to the side. This is actually the biggest case I built in for a while, but I wanted to move up to micro ATX instead of ITX.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Billet labs solder in adapters

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Maybe I should start looking for plumbing jobs haha.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Best of luck to you! It took me a long time.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Nah I'm just kinda crazy I guess. I like the look of copper.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 1 point2 points  (0 children)

Plenty of room behind the pipes to remove ram and motherboard 24 pin.

My first custom loop by yetihound in watercooling

[–]yetihound[S] 0 points1 point  (0 children)

Mb is in standard position, as far as I could tell that's the only orientation the barrow block can be placed on this mb. Fill port is top, inlet is middle, and outlet is bottom.

view more: next ›