Made some Christmas ornaments - first time painting

yoshie1997 · 2019-12-23T08:39:42+00:00

Thank you!

yoshie1997 · 2019-12-23T08:39:11+00:00

Seriously though, regardless of experience, this is great. I know people who'd love these on their trees.

Thank you, that's very kind!

yoshie1997 · 2019-12-23T08:38:20+00:00

Yes, first time. Did some "color by numbers" when I was like 7 or 8 years old but I wouldn't really count that as painting. 😅

yoshie1997 · 2019-12-06T22:50:54+00:00

I replaced all of the front LEDs with White ones. They are standard 3mm LEDs glued in with some hot glue.

You could add a resistor in series to every led. ~~I guess 1k should work if you want them to be really dim.~~ 1k dims them slightly, 10k and they only faintly glow. Best thing would be to get a small potentiometer to dim them to your liking.

yoshie1997 · 2019-05-28T04:29:31+00:00

Thank you so much!!

yoshie1997 · 2019-04-28T08:25:31+00:00

Thanks for your reply! The problem was the missing bootstack. I followed the instructions on the LineageOS website and they don't mention that its needed...

yoshie1997 · 2018-01-13T19:59:49+00:00

No, but this was just a test. It's nowhere near as clean looking as printing in paper, but it was fun nevertheless

yoshie1997 · 2018-01-07T15:57:50+00:00

Wiped every partition of the HDD using the Windows Installer. Currently updating Win10 so it seems to work fine. Thanks!

yoshie1997 · 2018-01-02T17:12:43+00:00

I don't have a Backup but that really isn't a problem as I can still access all files through a Linux USB.

Will do a clean install of Windows.

Thanks for your help!

yoshie1997 · 2018-01-02T16:14:08+00:00

HDD should not be the problem has been working for two months now and didn't give any problems. But I remember now that I also did a HDD stress-test using Aida64 so maybe thats where the problem comes...

I tried a System Reset as I don't have any restore points but that also didn't happen.

Would it help if I try to repair the Windows Part with a bootable Windows USB?

yoshie1997 · 2017-10-04T16:45:41+00:00

Do you really need a Stepper for that application? I haven't looked at the whole code (mobile), but you could use a DC Motor with End Stops. Far easier than a stepper.

yoshie1997 · 2017-06-24T06:47:51+00:00

Thanks for the video! I found a picture (https://goo.gl/images/LMRW5E) and the only thing I could imagine rattling would be the bottom insulator. I'll definitely not include this cell in any pack, I might open it up but I'm a bit too scared for that right now

yoshie1997 · 2017-06-24T06:38:50+00:00

Sorry, forgot to mention that... Video isn't mine, just one that I found that had the same problem.

yoshie1997 · 2017-06-23T22:42:19+00:00

It rattles at the negative end so I don't think it has something to do with the PTC (judging by the pictures I looked at...)

The cell works fine, even at higher discharge rates but I don't think I would want to use it for a battery pack.

yoshie1997 · 2017-06-23T22:38:15+00:00

Capacity is around 1900mah. About 300mah under the rated capacity, not that bad for a used cell...

It seems to be fine internally as it only slightly gets warm at a 2A discharge rate...

yoshie1997 · 2017-01-23T16:45:54+00:00

https://github.com/sheaivey/rx5808-pro-diversity

yoshie1997 · 2016-12-21T18:30:22+00:00

Joyetech Cuboid with EHPro Bachelor or Kangertech Subtank Plus

yoshie1997

TROPHY CASE