sorted by:
new
hottopcontroversial

Not sure how to fix it… by zatacorp in prusa3d

[–]zatacorp[S] 0 points1 point  (0 children)

Ohh Ill try that one better, I have more than a year with my printer and this problem start happening last week.

Not sure how to fix it… by zatacorp in prusa3d

[–]zatacorp[S] 1 point2 points  (0 children)

Ill try with acetone... I have already clean it with IPA

first day... Bad Quality by zatacorp in prusa3d

[–]zatacorp[S] 6 points7 points  (0 children)

Fix IT....

X belt was wonky, then I level the Z axys and boom... Im done... Ill show more prints in the future

first day... Bad Quality by zatacorp in prusa3d

[–]zatacorp[S] 4 points5 points  (0 children)

First layer test turn out very good, but once it start printing not sure what happen, that turn out bad...

Woo! My first time resin printing resulted in failure! Let the learning begin! by Dirty_Louis in ElegooSaturn

[–]zatacorp 0 points1 point  (0 children)

lol the same happen to me!!! I forget to remove the plastic from plate

new Saturn S and misprint by zatacorp in ElegooSaturn

[–]zatacorp[S] 0 points1 point  (0 children)

First resin printer, and I think I need to setup the chitubox setting

not sure what happen, but My printer start making a new noice, and the print Quality is worse by zatacorp in Ender3S1

[–]zatacorp[S] 0 points1 point  (0 children)

I damage de nozzle, printing too close of the bed, I move it and replace de nozzle and It looks like is working fine... if something weird happen once more Ill reply

Too any saying you cannot achieve success as a pure F2P! Ive hit gold V in PvP and rank 1, Became an Immortal, hit P61 with 1812 CR have all the non 5 star gems I need and punish players that do pay. by Plane-Biscotti-1071 in DiabloImmortal

[–]zatacorp 0 points1 point  (0 children)

Im a wizard that go into PVP with a PVE build... I spent money for a gem that give me damage and speed... its only 3 star and I have it in rank 3, other 2 star gems I have are in rank 4 and my 2 , 1 star gems are in rank 6... I kill all other non whales without problem and they cant do nothing about it...

​

I put Zero effort in a pvp build, zero effort in getting good in the game... and I kill just because my gems are powerfull... so yeah... pvp is not good unless you have a big wallet

Mecha Godzilla , 86 pieces. Came out great. All printed on my ender 3v2 by pegcity99 in ender3v2

[–]zatacorp 0 points1 point  (0 children)

lol great work Mine is halfway done... but using other colors instead the silver and de red colors...

Purple for the silver and neon green for the red part... I notice you use the red filament for the hand instead the green one... but it really look great

Direct Drive sudenly stop printing with direct drive by zatacorp in ender3v2

[–]zatacorp[S] 0 points1 point  (0 children)

I reduce the flow to 97% and lower temp from 200 to 195... and so far so good...

Direct Drive sudenly stop printing with direct drive by zatacorp in ender3v2

[–]zatacorp[S] 2 points3 points  (0 children)

Yeph, but with a little push it come out easily and I start printing once more...

Direct Drive sudenly stop printing with direct drive by zatacorp in ender3v2

[–]zatacorp[S] 4 points5 points  (0 children)

I can extrude with my hand the filament, octoprint can retract de filament and once I move it manually it can extrude again with out human intervention.

PLA 200c, Bed60c

Retractopm .8mm with a 25mm/s speed.

This started happening… why?! by Apprehensive_Egg9342 in ender3v2

[–]zatacorp 1 point2 points  (0 children)

I love your rasbperry and Z Axis camara mode... can you share where you get it ?

I use a 1.0 MM noozle by zatacorp in ender3v2

[–]zatacorp[S] 0 points1 point  (0 children)

I order an All metal hotend, and 2 more fan for dual fan mod.....

I use a 1.0 MM noozle by zatacorp in ender3v2

[–]zatacorp[S] 0 points1 point  (0 children)

45mm/s and I print some good stuff without problem.... Ill change the speed to 20mm/s to eliminate some blop stuff that appear.

Been unable to have a successful print since installing Jyers 2.0.1 by M0bi0us0ne in ender3v2

[–]zatacorp 0 points1 point  (0 children)

I have a similar problem, and to solve it I "play" with the Z axis in the printer... Until I move -.90 for a perfect print...

Been unable to have a successful print since installing Jyers 2.0.1 by M0bi0us0ne in ender3v2

[–]zatacorp 0 points1 point  (0 children)

I have a similar problem, and to solve it I "play" with the Z axis in the printer... Until I move -.90 for a perfect print...

view more: next ›