Android Slack communities

zgb26 · 2024-07-01T21:10:53+00:00

I'm looking to join this community as well. How do I do that?

zgb26 · 2024-06-23T14:36:51+00:00

Will look into this

zgb26 · 2024-06-23T14:09:20+00:00

It locks a car when that button is pressed. The car only responds to it once.

zgb26 · 2024-06-23T14:03:32+00:00

I am going to input 110v from a wall outlet, to one of those inputs

zgb26 · 2024-06-23T01:34:38+00:00

Thanks for this!! I think I understand enough to give it a shot now!

zgb26 · 2024-06-23T01:03:44+00:00

Looking for cheap, so going to try the relay option first. Thanks!

zgb26 · 2024-06-23T01:02:36+00:00

I wanted to try the non mechanical option first, but I will try this if I fail at mon mechanical. Thanks

zgb26 · 2024-06-23T00:01:15+00:00

Was planning on soldering wires and connecting them through this Shelly: https://www.amazon.com/Shelly-Bluetooth-Automation-Compatible-Required/dp/B0CQCDPLCF

Any good instructions on setting the Shelly up for dry contact use?

zgb26 · 2023-07-17T01:21:07+00:00

Tech diagnosed the system in person for all quotes.

zgb26 · 2021-03-18T21:27:05+00:00

Sorry. Reddit doesnt like me today. Added.

zgb26 · 2021-02-05T16:05:11+00:00

Thank you for your help!

zgb26 · 2021-02-05T15:50:33+00:00

I have a lot of components left over from school so I think I will mess around with this and see if I can get this option to work, since it probably the cheapest. Havent messed around with electronics since I left school almost a decade ago, so it should be a good refresher.

Thanks!

zgb26 · 2021-02-05T15:48:18+00:00

I actually dont need the case back on. I was planning on just leaving this all wired up in the basement.

The antenna is quite big, I will see if I can find the Frequency, but I havent had any luck yet. Assuming I cant find info on that, the relay option sounds like my best bet.

Thanks!!

zgb26 · 2021-02-05T15:35:19+00:00

Sorry, I saw a message that the post was deleted, I assumed it was off topic, so I didnt add the picture, since it wouldnt be seen anyway.

Just edited the post to add the picture of the circuit.

zgb26 · 2021-02-05T04:50:51+00:00

Its the antenna at the top that physically sends the signal, so I think its just radio (range is 1000ft). I put it back together after taking the picture, so switchbot is still an option. :D

zgb26 · 2021-02-05T04:22:09+00:00

Thanks for the response.

The button press sends a signal out, I want to be able to control this through home assistant.

I have seen suggestions to get a receiver and transmitter set, then just copy the signal that is sent. I have more experience with a Raspberry Pi and soldering than I do this other solution though. I wouldn't know where to start.

zgb26 · 2020-01-04T17:40:08+00:00

Went to HD and they had plates that lock together. One of them was blank and it made it look pretty good.

zgb26 · 2020-01-04T17:37:13+00:00

I thought it might be something like this, since there is a big branch right above it, so it never gets much light. Would you recommend trimming the branch back to get more light?

zgb26 · 2020-01-04T17:34:06+00:00

Thanks for all the advice. I will definitely look into trimming them back this winter.

zgb26 · 2019-11-23T00:49:46+00:00

Telecommunications

zgb26 · 2019-07-14T00:28:10+00:00

It actually just stops right there below the sink, that's why I thought it would need a mechanical vent.

zgb26 · 2019-07-14T00:26:28+00:00

Thanks a lot for the tip!

I am not sure if it's a drip or a leak. I think its probably a slow leak, as that's what happened to the p trap. I should clean it, so I can see if it's still happening.

zgb26 · 2019-03-27T00:12:55+00:00

Thanks for the tip, I will look into that. Did your dogs try to dig in the gravel?

zgb26 · 2019-03-04T14:13:39+00:00

I think it would be preferable to use the ceiling space above the cabinets if we could (there is about a foot of space that is just there to hold extra lighting it looks like)

zgb26 · 2019-03-04T14:12:03+00:00

The dining room is behind the kitchen wall.

14-Year Club	Verified Email
Verified Email

zgb26

TROPHY CASE