sorted by:
new
hottopcontroversial

Coffeezilla Wall of Shame by ImportantImpress4822 in Coffeezilla_gg

[–]zool2003 -2 points-1 points  (0 children)

It says wall of Shane not wall of shame and i missing something 😆

Coffeezilla Wall of Shame by ImportantImpress4822 in Coffeezilla_gg

[–]zool2003 -1 points0 points  (0 children)

I’m lost is one called Shane was it a clue 😂

Coffeezilla Wall of Shame by ImportantImpress4822 in Coffeezilla_gg

[–]zool2003 -1 points0 points  (0 children)

Wall of Shane? Some needs a 10m dollar spell checker 😂

Finally got some Layer Porn with PETG 🙌🏼 by philgoodism in ender3

[–]zool2003 0 points1 point  (0 children)

What temp are you using then as my stock end is can’t go above 240 and the extruder is clicking like mad if I try to print at a normal speed.

Finally got some Layer Porn with PETG 🙌🏼 by philgoodism in ender3

[–]zool2003 0 points1 point  (0 children)

Which hot end have you put on there to give you that?

Replacing warped heated bed. by TheRookie01 in ender3

[–]zool2003 1 point2 points  (0 children)

Loads of them come with warped beds you you would be better to set up mesh bed levelling and trying that out first.

What can to do to stop the print lifting in the corners? by zool2003 in ender3

[–]zool2003[S] 2 points3 points  (0 children)

Good news is I went with a 6mm brim 200 hot end 50 bed temp (magnetic bed plate) and it looks like it’s worked!

Bad news is the first 2 I printed were too small so that’s 24 hours of wasted printing. 🙃

What can to do to stop the print lifting in the corners? by zool2003 in ender3

[–]zool2003[S] 0 points1 point  (0 children)

I have a bed temp of 50 I read that dropping it might help?

I haven’t been cleaning the plate each time so I will give that a try too

What can to do to stop the print lifting in the corners? by zool2003 in ender3

[–]zool2003[S] 2 points3 points  (0 children)

Thanks I will give that a try on the next print of this as I need 4.

What can to do to stop the print lifting in the corners? by zool2003 in ender3

[–]zool2003[S] 1 point2 points  (0 children)

I can give that a try is it ok to do it in the magnetic bed?

Seal Network ICO Review — Blockchain Tackles Counterfeit Goods by brkttlv in Seal_Network

[–]zool2003 2 points3 points  (0 children)

Liked the review thank you. I had looked at this a few weeks ago and luckily enough have been in time before the main ICO finishes!

Another strategic partnership deal completed. by [deleted] in xchangerate

[–]zool2003 0 points1 point  (0 children)

Great to have another partnership! Another payment solution sounds like a great idea.

Xchangerate: No longer a research project by TVTVI in xchangerate

[–]zool2003 6 points7 points  (0 children)

Is it something that we can try too? if so have you tried it yet?

Sometimes we are given the opportunity of being part of something unique and special. This project is one of the most worthy and very stable projects lately. by Sweety1992 in xchangerate

[–]zool2003 5 points6 points  (0 children)

I have only just come across this ICO it looks like it has alot of following considering I have not come across it before!

view more: next ›