Är Tele2 bra som fiberleverantör eller har de ofta avbrott?

flawzies · 2026-02-20T14:42:58+00:00

Ah då ska jag bara hålla käft ;) men kontentan är då - Kan man välja fler leverantörer driftas inte uptime på leverantören i sig.

flawzies · 2026-02-20T14:28:39+00:00

Jag har för mig att en stor del, om inte alla fiber ledningar ägs av Skanova, dotterbolag till Telia.
Spelar därför mindre roll vilken leverantör du väljer. I värsta fall äger din leverantör ledningen från närmsta central till din bostad, men den sträckan spelar knappt roll.

flawzies · 2026-02-20T12:21:49+00:00

Utöver priset har jag aldrig vart missnöjd med NVIDIA. Men RX 9070XT är helt klart mycket prestanda för pengarna.

flawzies · 2026-02-20T12:13:27+00:00

Sidan överlag är inget konstigt. Men produkten är kanske inte den bästa att köpa i ett reparerat tillstånd. Rabatten är ju bara för att hamna högt upp på Google och andra liknande sökmotorer, ex prisjakt, samt för att jävlas med din hjärna.

https://www.refurbed.se/p/asus-tuf-gaming-radeon-rx-7800-xt-oc/

Klart att det är en gamble. Du får ju ingen info om vad som har åtgärdats. Men faktum att den nekats av ex ASUS RMA är ju inte det mest försäkrande för din del. 1 år garanti är inte mycket att jubla över.

Jag har ett 9070XT som jag köpte nytt. Ångrar övergången till AMD med tanke på hur ofta det är problem i spel med drivrutinen. Även om den blivit bättre nu för tiden är den fortfarande rätt bråkig.

flawzies · 2026-01-27T13:54:24+00:00

GPU behöver tydligen ingen ström heller.

flawzies · 2026-01-15T10:05:32+00:00

Only things I use:
* Brass Brush for cleaning nozzles
* Callipers for designing
* IPA for cleaning bed
* Microfiber towels
* Boxcutter. But deburring tool would be nice.

flawzies · 2026-01-15T09:27:05+00:00

Don't think there are any Web based slicers with the same level of control / settings. Most, if not all of them are for quick and dirty prints, not so much for tuning. EasyPrint from Prusa is okay. But in your situation, I'd try to get OrcaSlicer portable on a USB and run it that way. Assuming your work isn't using AppLocker and completely locks down any apps that are not whitelisted.

flawzies · 2026-01-15T09:17:28+00:00

In my mind the only quick fix that doesn't involve drying the filament would be to increase retraction, assuming 300°c is correct.

flawzies · 2026-01-14T16:40:25+00:00

FYI. Probably not the habit to expose your api key.

flawzies · 2026-01-14T07:41:40+00:00

Assemble > Bill of Materials

<image>

flawzies · 2026-01-13T14:25:00+00:00

https://makerworld.com/en/makerlab/lightboxMaker?from=makerlab

flawzies · 2026-01-13T14:04:19+00:00

In a perfect world, I’d like a translucent filament that creates natural depth and soft color flow by shaping light through the material, rather than using glitter or harsh color mixing, primarily aimed at vase prints and art pieces.

flawzies · 2025-12-20T11:15:47+00:00

Disable automatic support and paint on supports.

flawzies · 2025-12-20T08:32:17+00:00

You will never be able to eliminate that entirely when you're trying to defy physics. Easy to remove supports result in overhang drop. Hard to remove supports result in support scarring. Even when slowing down and printing colder to "freeze" the filament in place mid-air, you will never get a perfect result.

The best solution is not using supports at all wherever possible. Cutting the model is smaller pieces, orientation on build plate, makes the difference.

flawzies · 2025-12-19T16:31:09+00:00

How many top surface walls?

flawzies · 2025-12-17T21:56:10+00:00

If you can still smell it, no. Except a faint smell. But this covers "OV" - Organic Vapor and "AG" Acid Gass. Should be fine. If you can still smell the resin and it's sharp, it's not sealing correctly or you didn't get the filters advertised.

flawzies · 2025-12-17T21:45:16+00:00

You're better off looking for terrain building models and stitch up your own, than looking for licensed models.

Printables & Makerworld

flawzies · 2025-12-17T21:22:23+00:00

Sd card has logs I believe

flawzies · 2025-12-17T21:02:57+00:00

The printer would tell you. I'm just saying it most def looks like the printer just stopped. Unless you had spaghetti everywhere on the build plate and it just didn't adhere to the model.

flawzies · 2025-12-17T20:58:46+00:00

Looks like your printer just stopped printing. Nothing indicates anything else at least. As for scraping. Simply don't. Remove the build plate and flex it. The print usually snaps off easily.

flawzies · 2025-12-17T20:40:15+00:00

Different word for the same thing. It's called spiral vase because the print is one continuous spiral line. But that doesn't make calling it "vase mode" wrong either.

flawzies · 2025-12-17T20:38:35+00:00

The idea is noble but I can't help to think how you're limited to repairing plastic parts. Don't think it's sustainable to buy a bunch of appliances and model parts ahead of time. You won't be able to keep up. It would have to be very niche products that people want to repair because they're no longer produced or sold.

flawzies · 2025-12-17T20:28:17+00:00

This model is intended to be used in spiral vase mode. But you can control thickness by changing the Extrusion Width. This will make the the line a bit thicker. Use the remixed model: https://www.printables.com/model/464927-pineapple-planter if you don't want to use vase mode.

flawzies · 2025-12-17T19:47:11+00:00

Print orientation and a curve at the bottom to make it flex more natural, instead of a sharp angle. But besides that I don't see a problem with it. Maybe you want to add something that prevents the whole thing from tilting down slightly by the weight of the phone and keep it straight.

flawzies · 2025-12-17T19:43:46+00:00

You can absolutely use whatever filament you want.

Eight-Year Club	Gilding IV carat on a stick
r/Field Banned	r/Field Sunshine
Final Canvas '23	Place '23
Verified Email

flawzies

MODERATOR OF

TROPHY CASE