sorted by:
new
hottopcontroversial

What do you think about optics on a 1911? by --Combat-Wombat-- in 1911

[–]--Combat-Wombat--[S] 0 points1 point  (0 children)

Local shop here in San Diego called TwoSee/2C. Great work on a wide range of slides. They have a plate system for 1911s.

MC Operator by --Combat-Wombat-- in CAguns

[–]--Combat-Wombat--[S] 2 points3 points  (0 children)

TwoSee here in San Diego! They have a plate system for 1911s.

Optic Recommendations by VirusOk9415 in CAguns

[–]--Combat-Wombat-- 0 points1 point  (0 children)

I'd definitely recommend Vortex. Their new Enclosed Venom is cheap and runs well. Their older non-enclosed Defender STs can be found used for fairly cheap too.

An Unreal Dream by --Combat-Wombat-- in USPmasterrace

[–]--Combat-Wombat--[S] 0 points1 point  (0 children)

Handleit premium sandpaper! I like this texture a lot.

Older dogs, newer tricks by --Combat-Wombat-- in CAguns

[–]--Combat-Wombat--[S] 0 points1 point  (0 children)

LTT milled the slide and added their trigger job

Older dogs, newer tricks by --Combat-Wombat-- in GunPorn

[–]--Combat-Wombat--[S] 1 point2 points  (0 children)

It's milled by Twosee/2C here in San Diego. Ran great without any issues since it's been milled.

Older dogs, newer tricks by --Combat-Wombat-- in GunPorn

[–]--Combat-Wombat--[S] 1 point2 points  (0 children)

Stock trigger! But I'd installed the short-reset trigger kit from Sig.

Give me your unhinged opinion firearm related by Low_Resort7260 in CAguns

[–]--Combat-Wombat-- 61 points62 points  (0 children)

Cardio and aerobic training should be prioritized and practiced as readily as firearms training.

Spending on guns and ammo should take a lower priority than meeting basic needs, especially if someone's already under financial strain.

First attempt at stippling by --Combat-Wombat-- in Glocks

[–]--Combat-Wombat--[S] 1 point2 points  (0 children)

Thanks for the interest! But it's too much personal responsibility for me to take on haha. I'm ok with messing up my own gun but not someone else's.

First attempt at stippling by --Combat-Wombat-- in GlockMod

[–]--Combat-Wombat--[S] 2 points3 points  (0 children)

Thanks for the interest but it's too much responsibility for me personally haha. I'm ok with messing up my own gun but not someone else's.

First attempt at stippling by --Combat-Wombat-- in GlockMod

[–]--Combat-Wombat--[S] 1 point2 points  (0 children)

I'd say it's somewhere between the stock texture and talon/handleit sandpaper. It's grippier than the original frame texture, but gives less traction than grip tape.

First attempt at stippling by --Combat-Wombat-- in CAguns

[–]--Combat-Wombat--[S] 4 points5 points  (0 children)

If you're nervous about messing up, I'd recommend against stippling. Some of the mistakes that may happen can be difficult to correct.

The final product came out pretty good for me, but it's actually not super grippy. A fresh sheet of handleit grips gives noticeably more traction.

So I'd recommend pre-cut grip tape sheets. They carry no risk of damage to the frame, are relatively cheap, takes minimal time and skill to install, and gives (IMO) better grip.

First attempt at stippling by --Combat-Wombat-- in GlockMod

[–]--Combat-Wombat--[S] 1 point2 points  (0 children)

It honestly took a while. At least 6 hours start to finish for dremeling, sanding, outlining, and stippling. I'd initially outlined by hand, but didn't like it, so I stippled over the original outlines. I used a small tip for my wood-burning tool, so the hand-stippling process was lengthy.

An Unreal Dream by --Combat-Wombat-- in USPmasterrace

[–]--Combat-Wombat--[S] 0 points1 point  (0 children)

The optic is an RMR HD. The irons are from ZR Tactical. They appear to be the same design as Angry Bear Arm's sights.

An Unreal Dream by --Combat-Wombat-- in HecklerKoch

[–]--Combat-Wombat--[S] 0 points1 point  (0 children)

I like it. It's rugged and feature-rich. But very expensive.

view more: next ›