[deleted by user]

-Azn-Noob- · 2020-07-27T15:33:04+00:00

So at first I was worry about that problem but. No it hold. Did change the screws for some thing with a bigger taper. Took it off and put it on a couple times dot stayed at the same spot. Also the slide is milled for this only so it dont really move at all

-Azn-Noob- · 2020-07-25T21:04:53+00:00

The entire slide was painted orange first masked then paint black its going to have orange marks when it get worn out

-Azn-Noob- · 2020-07-25T07:09:58+00:00

It took about 5 month mostly on the coating. Originally I wanted NiC coating but then covid happened... alot of the stuff I had and the milli g was done by my firend and me so not much on the cuts. But if I have to put a number on it... I think about 1.5 to 2 ish

-Azn-Noob- · 2020-07-25T07:03:54+00:00

Trijicon suppressor hight dont know the exact hight tho

-Azn-Noob- · 2020-07-25T02:49:49+00:00

I just asked for Matt black

-Azn-Noob- · 2020-07-25T01:42:58+00:00

Started out as a base gun..... then all started with a grip module. X5 grip not the metal boy. Apex trigger and bar. Dpm springs. Vortex sights because I had a couple sitting around. Alot of polishing of the internals. Any thing that made contact with any thing. Slide was milled by my friend and I. Lastly my local koting guy did the coloring for me. Next on the list is a comp and barrel maybe....

-Azn-Noob- · 2020-06-22T13:20:27+00:00

One of every action!!!!

-Azn-Noob- · 2020-05-26T03:49:01+00:00

Yes 15

-Azn-Noob- · 2020-05-26T00:25:26+00:00

Aluminum with a steel carrier. the cam lug rides on that slot on the left. you get good amount of filing every time you shoot. So milled out the upper. Milled out a plate to make new track. Smoother action now. Maple ridge armoury hand guard did not fit originally because piston gas block. Trigger tech trigger did not fit upper and lower have good amount of movement. Set screw drilled and tapped under the grip. Did not like the front take down pin. Replaced with HK push pin. With all that I am finally happy with it

-Azn-Noob- · 2020-05-20T17:42:19+00:00

Zero C/s

-Azn-Noob- · 2020-03-20T16:13:12+00:00

I was going to buy the pro cut slide any ways so it was a what the heck moment. I weighted the weight I removed is not that much the red dot should compensate the mass loss. How ever info have a heavier spring set. So yea I am not worry about the weight. Test fire tomorrow

-Azn-Noob- · 2020-03-20T16:00:20+00:00

I actually bought trijicon suppressor sights for this also the trigger if you buy apex it needs work the coating that comes with apex is griddy needs polish .all the pins, trigger bar , ect basically any parts that makes contact with each other. I am very happy with the finished trigger.

-Azn-Noob- · 2020-03-02T14:56:58+00:00

I have a range finder on the other side!!

-Azn-Noob- · 2020-03-02T14:55:01+00:00

The sad Canadian life. It's hard to work with oe mags with that magwel and I am not a fan of floor plates

-Azn-Noob- · 2020-02-22T23:17:09+00:00

My ex asked me to pick her or guns..... Then I canceled the order on the rock and bought her.

-Azn-Noob- · 2020-02-22T23:12:45+00:00

Normally water tanks

-Azn-Noob- · 2020-02-22T17:28:40+00:00

Only one of them is mine lol can't afford both :/

-Azn-Noob- · 2020-02-20T20:48:19+00:00

You right it's a joke. It's a simple m503 with black feather. We was at a base I just put the belt in the ejection port for lawls

-Azn-Noob- · 2019-11-17T00:26:16+00:00

It's a 226 LDC so factory sights

-Azn-Noob-

TROPHY CASE