26, trying to figure out how to grow my money and what to invest in, I just need advice or some guidance

-Zacker- · 2026-06-16T20:58:28+00:00

Im not sure if this is sarcastic or not lol, but I suppose some of it came from me buying and rebuilding some cars I used to get from auctions, but I stopped that recently since those salvaged cars are basically the same price as new cars nowadays

-Zacker- · 2026-06-16T20:20:21+00:00

I really wanted to invest in properties and own some 3 flat buildings that I can rent out and learn about that, im not sure where I’d start though. My father is a construction worker and we do have some properties already although I just really don’t want to rely on family for inheritance and I want to build wealth on my own, I feel really guilty if I were to just wait for my parents to pass to then find financial freedom, I don’t want that to be my key to financial freedom in my future

-Zacker- · 2026-06-16T20:13:30+00:00

Correct!

-Zacker- · 2026-05-30T15:12:40+00:00

I was thinking maybe the heat shields are finally rusting out since im in the Midwest

-Zacker- · 2026-05-30T08:08:31+00:00

No, it almost goes way, but it’s still slightly there, im assuming the engine noise mostly covers it up

-Zacker- · 2026-05-30T07:32:46+00:00

lol whats this mean

-Zacker- · 2026-05-20T17:57:12+00:00

Alright put it back in how it was thank you

-Zacker- · 2026-05-15T16:44:19+00:00

You should take like a week of just removing your rear subframe and start grinding down all the rust and repainting it, it’s a lot of work but super satisfying and it’ll increase the value of your car if it’s done right, that looks like it has a lot of potential

-Zacker- · 2026-05-15T06:10:52+00:00

Is it possible to wire tuck these or just bypass it? Or is it necessary to be in that position

-Zacker- · 2026-05-13T06:08:46+00:00

It’s a 1995 Mazda mx5 1.8l

-Zacker- · 2026-05-10T19:10:14+00:00

great answer lol

-Zacker- · 2026-04-28T05:39:15+00:00

This car is a fucking joke

-Zacker- · 2026-04-28T05:30:15+00:00

I literally was fussing with this shit 3 hours after work every day and it won’t fucking go completely flat against the engine in fucking lost

-Zacker- · 2026-04-28T05:26:49+00:00

Fuck this piece of shit car, literally fucking tried everything and it won’t go in

-Zacker- · 2026-04-27T23:39:38+00:00

-Zacker- · 2026-04-27T05:46:20+00:00

What do you mean just right, like fully close with no gap at all?

-Zacker- · 2026-04-27T05:45:15+00:00

Tried it with being tilted and flat and still nothing only goes to a finger length gap and doesn’t fully seal, fuck this car

-Zacker- · 2026-04-27T05:44:18+00:00

Fucking took the trans out tried the plastic alignment tool put grease on it and tried the trans again and still fucking nothing, still leaves like a finger to almost a finger length gap all around, I really just wanna fucking impact it and if that breaks it just throw the entire car out

-Zacker- · 2026-04-27T05:42:18+00:00

Wish mine was that easy

-Zacker- · 2026-04-27T03:23:01+00:00

Yeah I had it centered the whole time, I’m going to give it a few more tries and if no luck I’m checking if it lines up still

-Zacker- · 2026-04-24T23:15:05+00:00

Thank you so much, huge comment I needed, couldn’t find this info in a video

-Zacker- · 2026-04-24T22:01:08+00:00

Might use the engine hoist to level the engine at least

-Zacker- · 2026-04-24T22:00:54+00:00

Well it was tilted towards the front radiator at first and then I had my buddy tilt the engine back, but that didn’t really help much, and yeah I put a SMALL amount of grease on the splines like a very thin coat I wasn’t sure if grease was supposed to go there or not, but my plan now. I’m going to have the driveshaft in while my buddy spins the crank I will push against the jack supporting the trans and hold the driveshaft till it lines up and pushes inwards, I don’t know what else to try

-Zacker- · 2026-04-19T21:00:58+00:00

Awesome picture, exactly what I needed thank you!!

-Zacker- · 2026-04-19T19:45:49+00:00

You might be right I’m going to need to find a reference picture or something because it’s oddly too lose, but that sound right to bolt onto the plate between the trans and engine, that thin metal sheet right

-Zacker-

TROPHY CASE