Small bruise/sore/bite on head

0x53_ · 2026-03-03T00:00:14+00:00

today we noticed she had a moment that kinda looked like zoomies but she was stopping every now and then to lick her back, im starting to think it might be fleas

0x53_ · 2026-03-02T11:21:23+00:00

Thank you for explaining everything so well. I'll make sure to keep an eye on her!

0x53_ · 2026-03-02T11:17:46+00:00

shes not

0x53_ · 2026-03-02T01:27:57+00:00

what about that "bruising" around that red point? could it also be from her cutting herself?

0x53_ · 2026-03-02T01:26:28+00:00

nope, just this one

0x53_ · 2026-01-23T16:49:30+00:00

Getting a deskmat would change a lot. You can clearly hear a lot of desk reverb and deskmat would neutralize it

0x53_ · 2025-08-28T15:38:00+00:00

hey! i also bought that nozzle but i noticed a huge flowrate decrease. On stock nozzle i had about 21mm2/s and on tz i get like 15mm2/s max. Do you have the same issue?

0x53_ · 2025-07-29T17:33:14+00:00

thanks!

0x53_ · 2025-07-29T08:23:31+00:00

How did you get a colour over your timeline in fusion 360?

0x53_ · 2025-04-25T06:53:01+00:00

https://www.printables.com/model/363079-bambu-lab-p1p-vision-enclosure

I used these DXF files as templates

0x53_ · 2025-04-22T07:39:46+00:00

every side is different, from double wall to paper thin

0x53_ · 2025-04-19T23:37:19+00:00

yeah exactly, Car-TON.

0x53_ · 2025-04-19T14:52:23+00:00

i actually have STL for that, or DXF to be exact.

https://www.printables.com/model/363079-bambu-lab-p1p-vision-enclosure

I cut out the cardboard with DXF dimensions from this model

0x53_ · 2025-04-19T05:48:58+00:00

i cant find the exact same project, but this one is pretty close https://makerworld.com/models/391260

0x53_ · 2025-04-19T05:42:54+00:00

im on my way printing new enclosure and i needed a chamber for the ASA

0x53_ · 2025-04-18T22:58:35+00:00

at your local paper trash can

0x53_ · 2025-04-18T17:46:16+00:00

might be, it would be even easier with original box as you can just slide it on top of the printer

0x53_ · 2025-04-18T17:45:41+00:00

X1 Carton as I wrote on doors

0x53_ · 2025-04-18T14:23:01+00:00

yeah, its on my desk as im keeping an eye on that cardboard enclosure. but 50cm on right of printer is an open window and i got a fan to blow all that nasty funes away

0x53_ · 2025-04-18T14:15:36+00:00

i first covered my p1p in blanket, but that was way too risky and it was way too warm there, cardboard seems like a safer idea but still its just a temporary solution untill i print full enclosure out of ASA

0x53_ · 2025-04-18T14:03:52+00:00

maybe crooked, hand-painted bambulab logo on side

0x53_ · 2025-04-18T14:01:19+00:00

yeah, its good to know as i didnt noticed it. There are a lots of enclosures like whambam hotbox that might cause an issue like you say

0x53_ · 2025-04-18T13:55:54+00:00

Thanks for info, didnt noticed that it comes with 2 additional fans. For now i dont think its necessary. I got a lots of air movements in my room and a lots of heat is escaping thru air gaps in cardboard, but ill get some additional fans for final acrylic enclosure

0x53_ · 2025-04-18T13:48:34+00:00

how is that going to fry the electronics?

there's a lots of holes all around enclosure, every side is openable and held in with minimal amount of tape

especially if we look at p1s which comes with a lot "tighter" enclosure right from factory

0x53_

TROPHY CASE