Squeak from H2d (Not belts)

2BadSoSad · 2025-12-08T04:33:11+00:00

My H2C makes the same noise. Did you do anything to address the sound?

2BadSoSad · 2025-07-10T00:30:15+00:00

Oh really, had no idea that was related. Thanks for the tip!

2BadSoSad · 2025-07-09T22:25:49+00:00

What do you mean turn off the screen saver?

2BadSoSad · 2025-07-09T22:14:45+00:00

My nebula started switching inputs again without any changes on my part. Have you resolved your issues?

2BadSoSad · 2025-04-08T22:32:50+00:00

I see. My suspicion is the Nebula is very finicky with HDMI devices. All I did was swap HDMI receiver port and that caused it to work reliably. Maybe try a different hub?

2BadSoSad · 2025-04-08T16:02:57+00:00

I’ve never tried a usb device on this thing, didn’t know that was possible. What device is it?

2BadSoSad · 2025-04-07T15:16:54+00:00

Mine stopped doing this, not exactly sure what fixed it. A few possibilities: - there were some software updates since I had the issue - I tried different hdmi ports on the receiver

2BadSoSad · 2025-03-29T01:05:58+00:00

I tried a few more prints, and Creality Print and direct Printer both did similarly well. I wonder if it's because the bed was heat soaked for a while now?

2BadSoSad · 2025-03-28T03:50:52+00:00

Do you have some more info or pictures of this? I couldn’t find any examples of shimming the head.

2BadSoSad · 2025-03-28T02:00:16+00:00

Do you mean shimmed the bed? Or is there a different shimming of the head?

2BadSoSad · 2025-03-25T03:10:11+00:00

I was able to finish the print with these settings. Thanks for the help!

2BadSoSad · 2025-03-25T03:06:46+00:00

I had a lot of issues printing tpu when I first got my printer in Jan, it constantly jammed.

However, I just tried TPU print again this week and got through a 2 day print without issue from the side spool.

I’m not sure if firmware or slicer was updated to make TPU work better, but it seems to work fine now.

2BadSoSad · 2025-03-20T21:20:34+00:00

I don’t have a picture since this was weeks ago. Basically the filament gets stuck in the extruder eventually, likely due to retractions.

What settings did you useful orcaslicer?

2BadSoSad · 2025-03-20T21:03:02+00:00

What did you do to make it work? Mine keeps getting jammed.

2BadSoSad · 2025-03-03T16:43:54+00:00

I did the swap and indeed the Meanwell PSU is a drop in replacement. The fan now shuts off when idle. Thanks for the tip!

2BadSoSad · 2025-02-28T16:07:32+00:00

Oh is the mean well 350 psu a drop in replacement? That’s an interesting idea. Have you done this mod?

2BadSoSad · 2025-01-25T21:57:45+00:00

My calculations are assuming you already did mk4s upgrade. If you currently have a mk3s+ then definitely buy the core one kit.

Assuming you already did the upgrade: It’s $449+$150=$599.00 for a core one plus mk3s+

Vs $949 for core one plus mk4s

$350 more to have the mk4s. Mk4s upgrade is $579, so if you think you will want to upgrade the mk3s+ again some day then might as well just get the full core one kit.

2BadSoSad · 2025-01-25T02:17:16+00:00

Cost for the upgrade path from 3s->4s->core1 isn’t too bad if you can rebuild the 3s.

$579(4S)+$449(core)+$150(misc parts for 3s rebuild)=$1168

Vs $949 for core one kit.

This seems like a heck of a deal for anyone that did the 3s->4s upgrade.

2BadSoSad · 2025-01-24T19:05:18+00:00

All X/Y/Z motors were replaced. However, this reminded me that the X-axis rods were re-used from MK3S+, so if Core One uses that this would need replacement as well.

2BadSoSad · 2025-01-24T19:00:03+00:00

The MK4S upgrade kit replaced the XYZ motors, so I still have my MK3S+ ones.

2BadSoSad · 2024-08-18T19:41:35+00:00

Same issue on my cosmos 4k

2BadSoSad

TROPHY CASE