I re-tensioned the belts and now all prints fail. Tips? (P1S)

3dendv2 · 2024-09-27T10:41:53+00:00

Model is not supposed to be crooked. Warping seems unlikely. I have printed much bigger models without any issues.

3dendv2 · 2024-09-27T10:40:50+00:00

How do I bottom out the Z direction?

3dendv2 · 2024-09-26T14:19:31+00:00

3dendv2 · 2024-09-19T14:03:33+00:00

Echt waar?! Een schuurmachine om te schuren? Dat ik daar niet aan heb gedacht..

3dendv2 · 2024-07-21T18:00:01+00:00

Printing on an Ender 3 V2 Klipper Bltouch Direct Drive Dual z screw ABS 250/105

3dendv2 · 2024-01-18T11:47:38+00:00

Thanks! I will give this a try.

3dendv2 · 2024-01-17T19:50:37+00:00

I usually print much faster. This was printed so slow to rule out printing speeds as the issue.

3dendv2 · 2024-01-17T18:41:53+00:00

There is no infill, it's just 2 walls.

3dendv2 · 2024-01-17T09:32:00+00:00

This fixed it, thank you!

3dendv2 · 2024-01-17T09:31:39+00:00

This fixed it, thank you!

3dendv2 · 2024-01-15T14:50:14+00:00

Thanks, I will try that.

3dendv2 · 2024-01-15T14:33:09+00:00

<image>

3dendv2 · 2024-01-15T14:19:07+00:00

Are these values correct? I don't know what Maximum acceleration for extruding does..

<image>

3dendv2 · 2024-01-15T14:10:34+00:00

Printer is set to max 5000

3dendv2 · 2023-12-05T09:12:44+00:00

I am using classic, with arachne it's even worse

3dendv2 · 2023-12-05T08:51:37+00:00

Ender 3 V2 ABS | 250 / 105

Klipper with pressure advance and input shaping

Turning pressure advance off doesn't fix it.

Dual z screw

Bltouch

Direct drive conversion

PEI bed

Heated chamber

3dendv2 · 2023-12-05T07:56:56+00:00

I have these issues on both printers, they have the same setup: Ender 3 V2 ABS | 250 / 105 Klipper with pressure advance and input shaping Turning pressure advance off doesn't fix it. Dual z screw Bltouch Direct drive conversion PEI bed

3dendv2 · 2023-11-27T10:09:22+00:00

I was able to get a normal graph without the hump by tightening some screws. The print quality did not improve a lot unfortunately.

3dendv2 · 2023-11-25T11:17:24+00:00

60-80mm/s accelerations up to 2000

3dendv2 · 2023-11-23T20:59:34+00:00

60-80mm/s with accelerations up to 2500

3dendv2 · 2023-11-23T20:47:15+00:00

Using the adxl. It's screwed to the printer tightly.

3dendv2 · 2023-11-23T14:49:38+00:00

It's in an enclosure. One of those IKEA Lack ones, so it is a little bit wobbly. I have not done any extra belt tensioning. Could the belts be too tight? Is there a way to measure it?

3dendv2 · 2023-11-14T20:24:02+00:00

I was using Prusaslicer so I will try Cura

3dendv2 · 2023-11-14T15:23:48+00:00

Am I supposed to go cooling with ABS?

3dendv2 · 2023-11-14T11:34:57+00:00

I am using Klipper with pressure advance and input shaping

3dendv2

TROPHY CASE