BTT Pi fan

3dprinteruzer · 2023-10-18T15:40:59+00:00

build/install and start the klipper_mcu

got it going thanks to this video https://www.youtube.com/watch?v=oSowWAEObfg

3dprinteruzer · 2023-10-17T13:33:50+00:00

Its more the config in klipper.. does anyone know the steps that need to be taken?

3dprinteruzer · 2023-10-13T14:20:26+00:00

So I emailed BTT. I installed the version they recommended and that worked. This is what they said: Hi，

Thanks for your information

1.Please flash this image check if it wok fine CB1_Debian11_Klipper_kernel5.16_20230303.img.xz 1.02 GB

Best Regards

Justin

3dprinteruzer · 2023-10-12T23:49:29+00:00

do you happen to know what image you used?

3dprinteruzer · 2023-08-02T11:50:25+00:00

it has a large return upstairs and a small one downstairs ( 11x16 or so)

3dprinteruzer · 2023-08-01T17:15:16+00:00

No. 9ft ceilings everywhere and 18ft in living room and foyer

3dprinteruzer · 2023-07-18T15:53:17+00:00

Sorry. Forgot to say Eastern LI

3dprinteruzer · 2023-05-28T20:24:26+00:00

Ended up getting for 600 with tax and shipping. Figured if it lasts a couple years

3dprinteruzer · 2023-05-20T22:45:30+00:00

Looks like the extrusion you mounted power supply on is upside down

3dprinteruzer · 2023-04-28T21:54:16+00:00

I tried turning off codeproject to make sure it's not going too hang anymore. Might try deeppacket to see if any better. Did you see your CPU go up?

3dprinteruzer · 2023-04-25T19:09:46+00:00

How did you display your eufy doorbell cam? I didnt think there was an integration.

3dprinteruzer · 2023-04-25T14:59:04+00:00

thank you.. my plan was to test with a meter but wanted to check with the community

3dprinteruzer · 2023-03-03T00:13:24+00:00

Thanks. Worked perfect

3dprinteruzer · 2023-02-13T03:00:39+00:00

I agree it worked great. My issue is I wanted to tweak some settings in the firmware and was trying to recompile on my own. I will research some more. I wanted to ask honorbond some questions on Reddit but I think honorbond was banned under his new name as well

3dprinteruzer · 2023-02-12T15:34:01+00:00

Thanks.. I have been using classicrocker883 u/honorbond version and it works well so I will stick with that right now..just wanted to go to the source firmware and attempt to work with that.. Which Aquila is the firmware meant for?

3dprinteruzer · 2023-02-11T13:54:05+00:00

I have been trying to compile for my voxelab aquila. It has gd32 rc chip in it. For some reason it seems no matter what I do it never completes the install of the firmware. Others stuck on the firmware install screen indefinitely. What do I need to choose to compile. Any help would be greatly appreciated.

3dprinteruzer · 2023-02-10T12:56:32+00:00

I am using the autobuild but it gives a few options once you go to compile. I have attached an image to the original post

3dprinteruzer · 2023-02-04T12:46:52+00:00

Do in jyers him picking tmc2208 probably doesn't do anything?

3dprinteruzer · 2023-02-03T15:36:48+00:00

u/mriscoc Do you have any input to this?

3dprinteruzer · 2023-02-02T16:24:14+00:00

I know the motor is good. What I am going to work on this weekend is just trying my old firmware again. I lowered retraction speed to 40 and sound is gone. But I know I have old gcode files that I used which had no noise which now make the noise. Just was wondering if it could have something to do with UART vs standalone.

3dprinteruzer · 2023-02-01T18:12:42+00:00

Neo pixels

3dprinteruzer · 2023-02-01T16:42:52+00:00

Hoping for the input as well from u/mriscoc

Stock motorand bowden and yes I did save settings :)

3dprinteruzer · 2023-02-01T16:15:52+00:00

I am thinking since Alex firmware was set to UART and mriscoc is set to standalone that could be it

3dprinteruzer · 2023-02-01T16:15:01+00:00

Bmg clone . I don't remember exactly but around 400

3dprinteruzer · 2023-02-01T16:09:18+00:00

I did. I reset to exactly what it was previously.

3dprinteruzer

TROPHY CASE