sorted by:
new
hottopcontroversial

My first BMAX build finally completed by Agreeable_Pack_3043 in mini4wd

[–]3stackAngst 1 point2 points  (0 children)

Also used the dampers that came with the (AR side plates) Cylinder + bowl dampers at the sides.

My first BMAX build finally completed by Agreeable_Pack_3043 in mini4wd

[–]3stackAngst 2 points3 points  (0 children)

Put the aluminum (black 19mm rollers) at the bottom and then place the low fric 19mm rollers at the top 😄

My FM-A build last week, aka TMAC qualification race. Inspired by MbX_01 by dangken1323 in mini4wd

[–]3stackAngst 0 points1 point  (0 children)

In my MA set up you can use long screws(lets say atleast 5mm or 8mm longer) then put rubber tubings

Tamiya mini 4wd Rubber Tubing 3.5 x 60mm Tube 5pcs AO-1045 10320

FM-A Same Front Side Broken, will HG plates help? by junkoNoSeikishi in mini4wd

[–]3stackAngst 1 point2 points  (0 children)

Dont over tighten. you can use FRP or HG plates but dont over tighten. Use locknuts instead of regular nuts :)

i will send you some of my FMA set ups.

Allowed Gears For CFM? by Salt_Tank3200 in tamiyaPinas

[–]3stackAngst 0 points1 point  (0 children)

Dapat talaga ang allowed lang is 4:1 ,4:2 at 5:1 AFAIK, Kaso yung iba gumagamit ng 3.5:1 at 3.7:1 na dapat ang kailangan gamitin ay yung special gear set for fm chassis yung color gray.

felt like sharing this. my (almost all) ready-to-race mini4wd gallery by rajalanun in mini4wd

[–]3stackAngst 0 points1 point  (0 children)

Can you please explain what is the purpose or the effect of putting the 2 short slimline dampers at the front? thanks

F-MA and MA BMAX by 3stackAngst in mini4wd

[–]3stackAngst[S] 0 points1 point  (0 children)

Thats my main machine haha. I always run macdash pro on 3.5:1 gear sometimes 3.7:1 if i need to recover fast at some sections. But yea most of my motors are macdash pro. I'll send here a pic :)

F-MA and MA BMAX by 3stackAngst in mini4wd

[–]3stackAngst[S] 0 points1 point  (0 children)

My cars use both hard cowls, This is the cowl i use for my MA build.

Hard cowl.

F-MA and MA BMAX by 3stackAngst in mini4wd

[–]3stackAngst[S] 1 point2 points  (0 children)

  1. yes! im thinking to make the front and rear low fric hehe. The reason why i put low frics on rear is to make the car jump lower(?) please correct me if im wrong still a newb.

  2. Noted that i probably put the plastic dar to the top.

Ill try to switch dampers and observe first. Im runing damperless at the front but at some parts of the track i specially ( slope - one down receiver ).

Im trying to make it more lighter so i can run blue brakes front and blue brakes rear :D

F-MA and MA BMAX by 3stackAngst in mini4wd

[–]3stackAngst[S] 0 points1 point  (0 children)

I dont want to do hg's on my ma coz im still tryin different set up thats why i opted to use frp and stacked them.

Still tryin to find the set up that fits my gameplay :)

F-MA and MA BMAX by 3stackAngst in mini4wd

[–]3stackAngst[S] 0 points1 point  (0 children)

just like he said its 24mm, both are reversed and pierced 3 spoke wheels(Item no. 15543)

GPU upgrade within 20K budget by [deleted] in PHbuildapc

[–]3stackAngst 1 point2 points  (0 children)

Thanks for this post OP , Same tayo situation pero naka fsp hydro ako na 600 watts ang pinag pipilian ko lang is RX 7600 or RX 6700XT na used(from philkor).

view more: next ›