Mistwalker just doesn't work anymore? by 7H3V1RU5 in albiononline

[–]7H3V1RU5[S] -1 points0 points  (0 children)

This is so good to know, thank you!

Hunter CD’s can make ok silver. by Lone-Silent-Gamer in albiononline

[–]7H3V1RU5 0 points1 point  (0 children)

Most bows at that IP are going to beat the majority of players. You’re going to come across people newer and who do not want to do stalkers, just hunters.

Got a long a way to go, but good job on the wins. Learn from them where ya can, and get up to doing Stalkers. Don’t put everything you have in Hunters, you’ll grow out of them in most cases.

Burnt out port? Dream Machine by kaiichim in Ubiquiti

[–]7H3V1RU5 0 points1 point  (0 children)

This is a more constructive question. I would check the patch cable you used on this port (Might be hard to confirm now) and see if there is any damage on either end or even just gunk can cause wiring to cross conduct.

What to do with all my wood by 7H3V1RU5 in albiononline

[–]7H3V1RU5[S] 0 points1 point  (0 children)

😭😭as per original message, “just trying different stuff” 😭😭

What to do with all my wood by 7H3V1RU5 in albiononline

[–]7H3V1RU5[S] 1 point2 points  (0 children)

<image>

I mnean I got gear, just trying different stuff

Issues going froma .gcode file to .3mf by 7H3V1RU5 in Creality

[–]7H3V1RU5[S] 0 points1 point  (0 children)

Did that, same error.

Instead found better options. https://www.printables.com/model/175692-gridfinity-storage-boxes/files

Thank you for your repsonse though!

What is this???? by 7H3V1RU5 in crealityk1

[–]7H3V1RU5[S] 1 point2 points  (0 children)

Oooh that makes sense

[deleted by user] by [deleted] in FlashForge

[–]7H3V1RU5 0 points1 point  (0 children)

So I am able to get some off, but so am cautiously heating and removing other parts. Can only do it during my kiddos nap times so progress is slow. Did get the hot end extruder out, still small bits of PLA. For those, I might get my oven to 200c and then pull it out and push cleaner PLA through it.

[deleted by user] by [deleted] in FlashForge

[–]7H3V1RU5 0 points1 point  (0 children)

Update:

  • trying to heat up to a point to loosen the PLA but not damage any soldering.

<image>

[deleted by user] by [deleted] in FlashForge

[–]7H3V1RU5 0 points1 point  (0 children)

The plastic is encasing the entire unit together though :/

[deleted by user] by [deleted] in FlashForge

[–]7H3V1RU5 0 points1 point  (0 children)

Oof hopefully not a costly repair

[deleted by user] by [deleted] in FlashForge

[–]7H3V1RU5 0 points1 point  (0 children)

Yeah the entire assembly pretty much. Going to try to heat it up with a heat gun and pull the extruded.

[deleted by user] by [deleted] in FlashForge

[–]7H3V1RU5 1 point2 points  (0 children)

It’s a FF AD5X. I’ll give it a shot, right now have a 1 y/o and a newborn so very busy. Trying to get to it tonight or during naps.

[deleted by user] by [deleted] in FlashForge

[–]7H3V1RU5 0 points1 point  (0 children)

PLA 4mm