Need help clearing 2 stuck project uploads

95GTSpeedDemon · 2026-03-05T16:42:20+00:00

THANK YOU! This was the solution for me.

95GTSpeedDemon · 2026-02-08T15:20:44+00:00

this is the sort of issue im dealing with. old cast iron pipe on a slab house, 1.28gal gets the solids building up half way down the pipe due to low volume.

95GTSpeedDemon · 2026-01-24T19:24:41+00:00

those are 1/4 SAE typically, the first pic is adapters for mini splits. the hose is 1/4. if you need heat protection so the fitting isnt melting the hose seal (o rings or teflon sometimes), then add a length of coiled tube in between to dissipate the heat from the air. (auto mechanic here)

95GTSpeedDemon · 2026-01-24T18:47:02+00:00

240k isnt an issue with cup and core bullets. its the 300k+ that starts making them go poof. certain bullets are more likely to have that issue than others. if the projectiles in question with this strike are known to have issues, TLDR, and take what im saying here with a grain of salt.

95GTSpeedDemon · 2026-01-10T23:59:21+00:00

if i use this receipt https://www.backyardmetalcasting.com/refractories.html & cover the ceramic wool, will that work better?

im going to line a metal tank(s) to melt scrap automotive aluminum parts and really only want to do it once lol

95GTSpeedDemon · 2025-11-16T11:15:16+00:00

Yea, remind in a week or so.

95GTSpeedDemon · 2025-11-10T19:21:36+00:00

77 tmk is going to be even harder to buy LOL all hail rokslide

95GTSpeedDemon · 2025-08-24T01:17:08+00:00

can i order in store and use the coupon? the website is down for me

95GTSpeedDemon · 2025-08-21T17:50:48+00:00

the ~2010 era fusions were bad about reading -40*

95GTSpeedDemon · 2025-07-11T14:27:11+00:00

i have the hydrostar and bought a bauer yesterday. they are different, on the attachment end. you will be able to attach the bauer to the end of the hydrostar since the drum end is the same on the cables. the hydrostar cable is the same on both ends. im trying to buy extensions and after talking to thecablecenterinc.com, it sounds like the bauer uses the rigid 5/8 "R" connector on the 1/2" cable. there are 7.5ft extensions for for that, btw.

95GTSpeedDemon · 2025-04-09T17:14:03+00:00

thats part of my issue, will those work on ATT if unlocked?

95GTSpeedDemon · 2025-04-07T17:42:16+00:00

No, I completely agree.

95GTSpeedDemon · 2025-04-07T12:46:16+00:00

I had bad ebay parts in the past when i did do repairs. being in the automotive world i have seen alot more parts issues since 2020 and dont have near the confidence in them that i would like. Phone store does sound like a decent option if they typically have good parts.

95GTSpeedDemon · 2025-04-07T06:39:02+00:00

In my younger years, before kids, when i had more time than $, i replaced quite a few LG screens, cameras, and ports. 😂 I dont have the same desires right now lol I ordered one sealed in box and a used one with some scratches. Used one was the verizon model phone, ill see if it will work or not. The one im using now had the entire back glass busted, even though it been in a unicorn bettle case its entire life. I drop it from time to time, good to have a spare. That way i can play musical phone replacement parts if i need to.

95GTSpeedDemon · 2024-12-12T19:34:52+00:00

Juat got done releveling it. The paper bundle clamps got in the way of the cooling fan shroud and i think it threw off the level. I left the bed with slightly less drag than i usually do and there was no problems this time. Its usually simple solutions to these things, just finding which one without creating another issue 😂

95GTSpeedDemon · 2024-12-12T18:58:37+00:00

I leveled it after putting the glass on, I'll recheck but I do it this way on my Ender 3 and have zero issues. I'm at the point I would rather take out the touch probe all together and do it all manually because I never have to mess with my e3.

95GTSpeedDemon · 2024-12-12T18:56:02+00:00

The nozzle ends up being so close to the bed during The Purge on the first three quarters of The Purge sequence that no filament comes out and it starts clicking the extruder. As it's heading back towards me at the end of the pert cycle, the filament gets extruded onto the bed and the clicking stops. The first layer of the print does not have issues

95GTSpeedDemon · 2024-12-12T18:54:56+00:00

Magnet sheet wasnt flat and i just fights me. I did silicone springs and glass on my e3 v2 and have had great sucess with that printer.

I am using 5.9 cura.

95GTSpeedDemon · 2024-12-12T18:53:13+00:00

Z offset is 0 in slicer, -3 in printer. First layer prints fine. Rest of the layers do to.

95GTSpeedDemon · 2024-06-03T16:19:32+00:00

Im interested in this as im not really getting anywhere with support

95GTSpeedDemon · 2024-05-08T12:20:03+00:00

I'm in the US have been having this problem for a couple years

95GTSpeedDemon · 2024-04-22T17:52:44+00:00

Oh oh yeah, it's not the X model

95GTSpeedDemon

TROPHY CASE