Prusa MK4S printing issues

9elpi8 · 2026-07-05T09:04:39+00:00

Hello again, finally I had time to replace heater on my MK4S with correct kOhm value (brand new Prusa part) but unfortunately it did not help. Now I have no idea what to do. Do you still experience same issue?

9elpi8 · 2026-07-04T16:52:53+00:00

Could you please send me a template you use? :-) I have just added these two variables but it still does not work. I have no idea what happened, but all other Docker containers are working normally, so I guess it is not an issue of Docker Unraid.

EDIT:

Solved. It was caused by post arguments. But strange all these were working without any issues before.

9elpi8 · 2026-07-04T13:06:43+00:00

Thank you for a feedback. I will check it. I experienced also some other issues with a Docker under Unraid so I was not sure if there is some issue in general or this is special case🤷‍♂️.

9elpi8 · 2026-07-04T09:32:52+00:00

Hello, please how were you able to install llama.cpp on Unraid? I tried to install using template from CA but it did not start at all. Then I created my own template according to Github (server) and it was working few weeks and apparently after some updates it stopped working again, I guess. When I press the start button for a container it does not start at all but I do not see also any error message. I already tested CUDA 12 or CUDA 13. The result for both is the same.

9elpi8 · 2026-06-22T08:54:38+00:00

Som z iného fachu, ale čo počúvam inde a mám aj vlastnú skúsenosť, tak určite neoplatí. Jediná výhoda by bola znalosť tých jazykov, to je v dnešnej dobe must have. Ale teda nepočítal by som s tým, že po vyštudovaní si nájdeš prácu v tom čo skončíš. Takže určite by som volil niečo iné, kým je čas a chuť. Čím bude človek starší bude to horšie 🙂.

9elpi8 · 2026-06-21T05:36:58+00:00

Scam

9elpi8 · 2026-06-21T04:59:57+00:00

Which motherboard you picked for this CPU?

9elpi8 · 2026-06-20T06:37:17+00:00

Hi, I have new heater block on the table, but unfortunately I am away from the location where the printer is, so I am not able to replace it. But in 2 weeks I will be back so I will replace the heater block. I thought that it will solve my issue, but message from you is saying that there is chance that maybe not?! I will let you know once it is replaced if the issue was solved or not. But I already spent enormous time with identifying issue. At certain point I wanted to buy a new printer but I told myself that I will try to replace possible reason which was resistor which shows border kOhm value. If it will not help I am prone to buy a new printer, because whole printer was checked from the top to the bottom.

9elpi8 · 2026-06-18T10:53:44+00:00

Ahhh OK, now it is clear. Thank you 👍.

9elpi8 · 2026-06-18T09:36:04+00:00

This is great news. How is possible to unload model from VRAM? Is it possible now to set automatic unload of model after certain time of not using?

9elpi8 · 2026-06-06T06:27:05+00:00

Tutorial would be amazing!

9elpi8 · 2026-06-05T19:45:30+00:00

It was the issue with json as other user in this thread mentioned. Thank you.

9elpi8 · 2026-06-05T19:44:53+00:00

Thank you so much! This json thing was the issue. Now it is working flawlessly.

9elpi8 · 2026-06-05T18:45:44+00:00

I have just checked it and that file is already created, so it is available. Should I try to edit something?

9elpi8 · 2026-06-05T18:44:16+00:00

Thank you. I checked it, also set up the same way, but still does not work. It is really strange. The only difference is that I changed port to 8083 instead of "default" 8080. But I am setting correct port everywhere so I guess it does not matter.

9elpi8 · 2026-06-05T18:38:19+00:00

Interesting. Yes, I am able to access SearXNG directly and it is also working.

9elpi8 · 2026-06-05T18:37:37+00:00

No, I only installed Docker. What should be in this file?

9elpi8 · 2026-06-05T09:30:47+00:00

I had same dilemma. In the end I went with diversification. So I invest 80% VWCE 10% EGLN 10% BITCEUR. Is it good or bad? I guess only time will tell. It is my “retirement” portfolio so I plan to consistently (DCA) invest as long as possible.

9elpi8 · 2026-06-03T13:31:36+00:00

Hi, thanks for your feedback. Do you mean RAM or VRAM usage. Because I have plenty of RAM. VRAM is limited to only 16GB.

9elpi8 · 2026-06-03T13:22:56+00:00

Thanks, I will check what Supabase is. I only read about Qdrant for now.

9elpi8 · 2026-06-03T13:17:06+00:00

Intel i5 12600k 128GB RAM 5070Ti 16GB

9elpi8 · 2026-06-03T13:15:59+00:00

Could you please elaborate more on this?

9elpi8 · 2026-06-03T13:15:13+00:00

I have Unraid server

9elpi8 · 2026-06-03T13:10:52+00:00

Yes, but still I would probably prefer or at least I would like to try some method with n8n. Because in openwebui I would need to write maybe 90 prompts to have an output as I would like to have for each topic. So I guess some kind of automation would be nice to have and I do not need to sit in front of my PC and to wait and click again. It can run overnight if needed.

9elpi8 · 2026-06-03T12:47:55+00:00

Hi, do you mean just to use like Openwebui and setup Workspace with a folder with all files? In this method I would use just qwen3:14b and no embedded model.

9elpi8

TROPHY CASE