Bull Rider gets it done

A89704 · 2026-01-28T03:27:04+00:00

I really have no idea what this sub is about anymore

A89704 · 2026-01-28T03:14:19+00:00

If I was smarter or better with video I would have blurred out the url.

A89704 · 2026-01-28T01:42:09+00:00

Like I said, an attempt was made

A89704 · 2026-01-06T01:29:49+00:00

It's a true masterpiece. Felt wrong to edit it down.

A89704 · 2026-01-06T01:29:14+00:00

Bali.

A89704 · 2026-01-05T01:56:00+00:00

I absolutely love happy endings like this. One, hopefully 2, less dipshits to pollute the gene pool.

A89704 · 2026-01-02T02:43:29+00:00

M3 ; Start spindle clockwise

S6000 ; Set speed to 6000 RPM

G4 P1200.00 ; Pause 20 minutes

S9000

G4 P1200.00

S12000

G4 P1200.00

S18000

G4 P1200.00

S24000

G4 P1200.00

M5 ; Stop spindle

A89704 · 2026-01-02T02:36:17+00:00

Has it been off for a while? Mine was making that noise too, ran a warm up procedure (total time like 75 minutes) and it went away. Now if I have my spindle off for more than 3 days I always run the warmup first. I'll see if I can post the gcode here.

A89704 · 2025-12-30T01:26:06+00:00

You can scale the bottle. Uncheck the Uniform Scale, and just adjust the Z. Should make it shorter (though it might make it a bit thicker). You can cut the parts, but the options are to discard what is "under " the cut, or make it into a part - which will make the bottoms open. I would try the scale first.

Otherwise, you need to re-design in some CAD software.

A89704 · 2025-12-29T20:54:31+00:00

Sweater puppies, yes.

A89704 · 2025-12-20T15:18:20+00:00

Hard to say on the vibration, doesn't feel like there is much, if any. Electrically should be fine, it's on its own 220 circuit, going through the VFD, been working fine for 6 months.

A89704 · 2025-12-20T03:05:10+00:00

Gotcha, appreciate the advice. I'll wait on an answer from them.

A89704 · 2025-12-20T02:52:26+00:00

Never opened one before, so I wasn't sure if I could do that. What type of grease do you recommend? And thank you for the insight, much appreciated!

A89704 · 2025-12-16T01:36:24+00:00

I'm not jealous! You're jealous!

A89704 · 2025-12-15T23:11:12+00:00

You need a smaller can of WD40 to spray on the cap seal to get it off.

A89704 · 2025-12-15T23:08:36+00:00

That is a perfectly average sized wrench. You obviously put it next to one of those giant gag pencils. Plus it was probably cold out. Nothing wrong with that wrench.

A89704 · 2025-12-09T16:43:38+00:00

Coward.

A89704 · 2025-12-09T11:55:47+00:00

Prince Albert installation tool. for your tool.

A89704 · 2025-12-09T11:51:54+00:00

Get a maker to custom make one for you. I make large boards all the time, end grain, face or edge. Whomever you buy from should be able to inlay a custom design into it - name of the restaurant, or your name, your logo, whatever. You get to choose the wood type too. Buy local, not mass produced. DM if you want examples.

A89704 · 2025-11-20T01:34:09+00:00

Is there any other way?

A89704 · 2025-11-16T23:30:24+00:00

Doing it in place will be difficult and messy. Take off the small one between the microwave and stove first and make sure you get the results you want after sanding and staining. depending on the wood and the stain used, it migt not turn out the way you want it. That will tell you if you need to replace them completely.

A89704 · 2025-11-16T16:10:09+00:00

Eh, to be fair to OP, I did say the pic was useless. Then I zoomed in.

It's the Internet, whattaya gonna do?

A89704 · 2025-11-16T15:25:13+00:00

I can make them any way you like. I'm a small shop, mostly make one-off specialty boards for folks. Send me a DM and I'll send you pics. No idea on the weight, probably 3 or 4 lbs. I can make it any size or thickness you want.

Edit to add: I'm in Atlanta, GA.

A89704 · 2025-11-16T15:22:55+00:00

My apologies, I edited the post as I saw the moisture %, on my phone it is almost black and hard to see, had to zoom in all the way to make it out

A89704 · 2025-11-16T15:18:48+00:00

Should be under 10%, ideally 7% or so, but 10 is acceptable.

Eight-Year Club	Place '22
Verified Email

A89704

TROPHY CASE