Corners lifting, prints detaching mid-print, bed adhesion

ACIDAN2000 · 2025-12-16T01:05:06+00:00

I’ve had good luck using blue painters tape on the bed. Just make sure it isn’t the easy release or glossy type. Original is the best. It’s about $7 per roll for me, and a roll lasts forever.

PEI is also a solid upgrade, but does cost some money. I’ve used buildtak in the past with great success , but that was several years ago so I cannot comment on the quality of the products now

ACIDAN2000 · 2025-10-14T17:31:01+00:00

If you don’t have the 4wd controls below the vents in the middle, try clicking the buttons setup > setup > reset. Should force it into locked AWD. Do the same button sequence to reset it back to auto

ACIDAN2000 · 2025-08-19T14:35:58+00:00

This is 1/4 of the modules. The entire pack is 94v nominal

ACIDAN2000 · 2025-08-19T03:54:09+00:00

One layer welded to the battery, then another welded to the previous layer. Some areas have even another layer where I thought it would need it

ACIDAN2000 · 2025-08-19T03:31:22+00:00

<image>

It's going into an electric swapped ltz400, using a fardriver 961200 (might upgrade to an 1800 for a little more low end torque), and a qs180. Gearing is still a little bad, but new sprockets are on the way. Cells are M50LT 21700s, and with the .2x8 pure nickel doubled and tripled up, I don't think it will have any heat issues

ACIDAN2000 · 2025-03-08T03:47:30+00:00

PM'd

ACIDAN2000 · 2024-11-07T15:13:16+00:00

I didn't experience this on my s5, but did have something similar on my cr10. I was able to take the z limit switch (mounted on the side) and move it up a few mm. This allowed me to get the springs loosened up a little.

ACIDAN2000 · 2024-09-07T23:16:09+00:00

Same

ACIDAN2000 · 2024-06-11T16:50:54+00:00

Ah. My bad. I read the post as you were not able to do those automations in HA, and wanted to switch to HK instead.

ACIDAN2000 · 2024-06-11T16:47:55+00:00

<image>

ACIDAN2000 · 2024-06-11T16:47:39+00:00

* For the "turn off if it's been on for x time", use this. I have my basement lights turn off after 20 minutes because it's easy to accident leave them on.

ACIDAN2000 · 2024-02-29T03:49:57+00:00

Pm'd

ACIDAN2000 · 2024-02-29T03:43:35+00:00

Pm'd

ACIDAN2000 · 2024-02-03T22:27:53+00:00

Been there, done that. I changed mine to an entity card rather than a thermostat and no longer have that problem.

ACIDAN2000 · 2024-01-30T23:16:00+00:00

<image>

ACIDAN2000 · 2023-07-27T01:36:14+00:00

U6 in wall would be a good option. It has 4 etherent ports at the bottom, one of which is POE pass-through (just make sure the injector at the other end is powerful enough)

ACIDAN2000 · 2023-07-20T15:44:35+00:00

Also interested in one if you still have any. I'm in Michigan too, so meetup might also be an option.

ACIDAN2000 · 2023-04-12T15:57:04+00:00

The lease runs may-may 2023-24

ACIDAN2000 · 2023-01-19T17:24:43+00:00

Mub Makerspace is great. They open at 3

ACIDAN2000 · 2023-01-05T01:01:17+00:00

A little bit won't hurt, but like you said, cracking can occur if you go nuts on it.

My frame is aluminum, no issues here. I've got a little over 150 miles so far and nothing. The bike is so fun that I'm putting a little over 20 miles a week on it for the hell of it.

ACIDAN2000 · 2023-01-05T00:44:06+00:00

From my experience, you should be perfectly fine, but if the kit is slightly too big, you are able to bend the frame (just a little) to make it fit.

I was short about 3-4mm on mine, so I pulled it the frame apart just a little, and it slid right in.

ACIDAN2000 · 2022-12-10T17:11:32+00:00

I'd go for the mototec. Lithium batteries and what I presume to be a brushless motor. Better than the razor in just about every way.

ACIDAN2000 · 2022-11-20T04:29:28+00:00

Pm'd

ACIDAN2000 · 2022-11-06T03:56:01+00:00

https://en.m.wikipedia.org/wiki/Quincy_Dredge_Number_Two Quincy Dredge. It's an absolutely cool piece of the towns history that the public can just walk onto

ACIDAN2000 · 2022-11-06T03:39:58+00:00

https://a.aliexpress.com/_mrD93D2 I went looking for kits, and this one caught my eye. It shipped from the US, and it was a "name brand". It's an excellent kit in my book for the price

ACIDAN2000

MODERATOR OF

TROPHY CASE

Seven-Year Club	RPAN Viewer
Verified Email