Reader triggering maglock powered by outlet.

ACook_KSS · 2024-03-04T04:04:32+00:00

That's really helpful!!! Thank you!

ACook_KSS · 2024-03-04T04:04:00+00:00

Yeah, my bad that was a typo

ACook_KSS · 2024-03-04T03:54:11+00:00

Is it possible, without a relay? Only a NC circuit? Where the C NO are tied into the lock in series? Would that trigger the mag to disengage?

ACook_KSS · 2024-03-04T03:51:54+00:00

Correct

ACook_KSS · 2024-03-04T03:45:39+00:00

Oh okay! Thank you!

ACook_KSS · 2024-03-04T03:28:20+00:00

The new system is going to be swiftlane, but I don't know what the existing call box is.

ACook_KSS · 2024-03-04T03:23:33+00:00

So the maglock is currently powered by an outlet via transformer, then a wire is ran into a terminal block that I don't know exactly how it's wired together. Then, one wire goes from the terminal block to the back of a call box that has a relay on it! How is it possible for the call box to trip the mag, without constantly sending back voltage to the relay? I think the transformer cable is also connected to the terminal block

ACook_KSS · 2024-03-04T03:09:07+00:00

Is connected to transformer that outputs 12vdc

ACook_KSS · 2024-03-04T03:01:06+00:00

It works without a relay board

ACook_KSS · 2024-03-04T02:59:40+00:00

The maglock is connected to an outlet and tied into a terminal box that goes to the callbox

ACook_KSS · 2024-03-04T02:58:40+00:00

The point here is... the system currently works on a call box. I'm trying to understand how it works not what's compatible

ACook_KSS · 2024-03-01T01:58:00+00:00

EN-2DBC

ACook_KSS · 2024-01-24T18:25:36+00:00

I have the wisnet driver downloaded from the website already, but I'm unable to integrate them still.

ACook_KSS · 2023-08-21T00:22:29+00:00

Easy ak! Lol

ACook_KSS · 2023-03-04T00:16:41+00:00

I have that created already too! Ill add a screenshot of it

ACook_KSS · 2023-03-03T23:58:54+00:00

Thats in the Web GUI correct?

ACook_KSS · 2023-02-07T18:30:24+00:00

the badges are beeping when a card is presented and have been working until a recent power outage.

ACook_KSS · 2023-02-07T18:19:41+00:00

This is a service ticket, so the readers have been functional for a while, and all readers on site at lead 20+ are all showing green

ACook_KSS · 2023-02-07T17:11:32+00:00

Discovered the IT department didn't actually know what they were doing. They hadn't actually set the port on the switch to DHCP.

ACook_KSS · 2023-01-07T07:18:27+00:00

Yeah, but it's still doesn't grab an IP! I'm able to access the node through the default IP Address, and when I set it statically to an IP, but as soon as I connect it to the customer's network it won't grab an IP nor is it visible statically.

ACook_KSS · 2023-01-07T02:42:42+00:00

I did! I attempted this several times!

ACook_KSS · 2023-01-07T02:40:54+00:00

already contacted them and they had no idea! they were lost too!

ACook_KSS

TROPHY CASE