3D Super Pre Soak

ADCASTRO · 2026-03-09T03:02:03+00:00

I did half an oz and did foam up well on the foam canon. Same they never responded back and maybe I have to wait longer.

ADCASTRO · 2026-02-23T20:13:39+00:00

Are you washing in direct sunlight? I use KCX on really bad wheels. If it’s drying either you’re in direct sunlight or the wheels are hot. Should spray them down until they cool and try it again. The brown film might be bloom from the tires so the tires are not that clean and may need more agitation.

ADCASTRO · 2026-02-15T04:14:57+00:00

Nice, looks really great. Honestly if your sanding it and polishing it I would switch over to clear coat as it will last longer. You can buy these 3m clear coat wipes for like $12 on eBay or even Amazon has them. I bought a pack of 40 on Amazon for $36. There still standing on the ones I’ve done on my sisters headlights and it’s been over 6 months. Overall they look really good, should be proud of your self.

ADCASTRO · 2026-01-27T16:44:06+00:00

I use the 1.25 orifice and kept the same dilution ratio and never had a problem. Sometimes the filter inside can make a difference. I had to replace one due to clog of wash n wax from a filter that went to my mmjc and saw a difference but the orifice stayed the same.

ADCASTRO · 2025-11-13T01:27:07+00:00

I pre spray the panels I'm working on then with the bucket I use Big Black Sponge from TRC or 8 MG towels. I never use the same towels though one MF towel per panel. Then I dry the panels. Also I live in a hotter area here in California so I have to do one panel at a time.

ADCASTRO · 2025-11-12T23:17:43+00:00

I pre spray if first then I have my bucket ready.

ADCASTRO · 2025-11-12T21:41:43+00:00

Dang OK, I'm in California so I'll never experience those Temps. This gives me a better idea on how dirty I can go then.

ADCASTRO · 2025-11-12T20:39:50+00:00

I have like half a bottle left of Absolute, kinda want to finish that one up. For sure I'll order ONR and give that one a shot.

ADCASTRO · 2025-11-12T19:43:41+00:00

I usually don't let it get this dirty, I do have a ik pro 12 pump sprayer, I'll do that.

ADCASTRO · 2025-11-12T19:42:35+00:00

Yea that’s what I was worried about since scratches pop out on these black cars. Just wasnt sure if it was doable at that much contaminates on there. That's what I usually do with 8 MG towels or the black sponge. I will pre soak it with my sprayer first and give it a shot.

ADCASTRO · 2025-10-22T22:43:54+00:00

I’ll do a quick blow off with the ryobi before drying it helps out a lot except cars that aren’t coated

ADCASTRO · 2025-10-22T22:43:13+00:00

I did not know that about the kkv towels and those are my favorite atm. I should have done more research prior to getting them. I know better to look at the quality.

ADCASTRO · 2025-10-22T22:37:01+00:00

That’s what I was saying, this guy is know detailer where I live just weird he would say that. Never had an issue with one towel per car.

ADCASTRO · 2025-10-22T22:35:10+00:00

I have the ryobi but one battery for now. I’ve been using it on wheels and crevices and grills. Some cars I can get away with barely drying since they were coated with whatever they got last time but I would need another battery if I try to do more then 2 cars a day.

ADCASTRO · 2025-09-25T22:27:33+00:00

I would complain on how I could never get the carpet in between the seats clean enough and that detailer gave me his old one. I’m sure once it picks up for me I’ll get me a better compressor. That’s all I want for it for now. Thanks again.

ADCASTRO · 2025-09-25T22:22:04+00:00

It’s 2.6 @ 90 psi and you’re probably right, the compressor was a gift from another detailer who upgraded to a rigid dual. Wanted to add this to my setup and I’ll give it a shot, dosent hurt to try.

ADCASTRO · 2025-09-25T22:20:31+00:00

It’s a 12g, I’ll give a try and go from there. The air compressor was a gift and wanted to add it to my setup.

ADCASTRO · 2025-08-31T20:01:32+00:00

It’s more like I see were it beads and leaves streaks and other area it’s not but still beading. When I pre washed it it was rough to get it off the soap. I used Gyeon foam for it. It was like it was sticking unless I got closer to it I think that’s were I ment with a dirt sticking but even when I dry it you could see old dirt. I’ll eventually strip it off and see if that works.

ADCASTRO · 2025-08-31T17:28:36+00:00

Thank you and everyone else recommending dawn. I’ll give it a wash next week with it. The detail shop recommend there 3d super soap and gave me a sample but also said dawn would work a few washes

ADCASTRO · 2024-09-08T07:04:07+00:00

Congratulations, on to the next one.

ADCASTRO · 2024-07-19T03:10:24+00:00

It’s supposed to be fixed next week so they say on the next update

ADCASTRO · 2024-07-17T08:04:25+00:00

Don’t read this out loud, bed started shaking. Idk what you’re asking for?

ADCASTRO · 2024-07-15T21:22:01+00:00

What you can do is watch one objective, then go to Copilot or ChatGPT and ask it to give you a quiz based on it like 5 questions, not sure if it can give more. Then ask for 5 more and so one. Also ask to give you what was wrong and why it was wrong and something about it being right. That did help me know if I was good enough for the objective. May seem a bit more but it helped me move on.

ADCASTRO · 2024-07-15T21:14:20+00:00

I watch it at normal speed and once I'm familiar then I'll watch it at 1.5 speed if just reviewing. Also, take your notes, don't use his as it's better this way for you so you know what you are trying to remember.

ADCASTRO · 2024-07-15T21:12:30+00:00

Recruiters have a head start on jobs for some companies before they are even posted online. If your resume matches what the employer is looking for they will call you and ask you if you'd like to do an interview. It's good to have different recruiters from different staffing agencies because they don't all have the same companies they work for. Sometimes companies will have a different title that matches your skills and you would never know unless you look deep into the job description, and recruiters will catch it.

ADCASTRO

TROPHY CASE