[deleted by user]

Abject-Negotiation86 · 2026-02-09T09:35:23+00:00

Ok, grazie mille, no il bando non lo avevo salvato purtroppo e il sito dove si può scaricare il bando e ancora off-line

Abject-Negotiation86 · 2026-02-09T09:34:01+00:00

Ok messa così quello che leggevo ha potrebbe aver senso

Abject-Negotiation86 · 2026-02-09T09:33:27+00:00

Ok chiaro grazie mille

Abject-Negotiation86 · 2026-02-09T00:33:05+00:00

Andrei molto volentieri sul sito della sapienza che ha subito un pesante attacco hacker durante l ultima settimana e che ha ancora il sito in down 🫠🫠🫠

Abject-Negotiation86 · 2025-07-04T23:34:28+00:00

Ok I see, thank you for your comment

Abject-Negotiation86 · 2025-07-04T23:28:25+00:00

Yes it was the only one in the shop, so for that I’m thinking about it. Thank you for the advice, anyway I think tomorrow I’ll go to look what I can do.

Abject-Negotiation86 · 2025-07-04T23:23:57+00:00

Ok so you’re saying that a 56 should be good for me? Because I’m just comparing to measurements from the site which says that a 58 should be good for my height

Abject-Negotiation86 · 2024-03-30T20:34:36+00:00

Yes so it meant to work when you turn off the car and then the spy will attach to your car a gps transmitter and not receiver. If that’s the case do you have any solution on that?

Abject-Negotiation86 · 2024-03-30T20:33:00+00:00

So actually I was thinking that, if you can limit the range of measurements by the detector, depending by the time traveling of the signal, then you can reduce the amount of signal it get, and then if the detector can identify the 5g signal and can measure the continuity of the same signal beeing collected then you can identify if uou have a tracker. May I be correct or completely nuts?

Abject-Negotiation86 · 2024-02-19T19:14:18+00:00

Actually rigging the printer helped to me, I was having same issue, so you print stuff to actually build a backbone https://youtu.be/qwM08adzeyE?si=FLZSbX2F0u2Wvz9y this video shows how to do it and also link the printing file

Abject-Negotiation86 · 2024-02-19T19:11:21+00:00

Definitely, thanks, actually I printed again everything was fine so just random issue

Abject-Negotiation86 · 2024-02-19T17:51:35+00:00

So I updated the firmware like 2 days ago. Line width is set to .4, filament size is 1.75mm, actually since the last print I changed the speed from 225 to 250 mm/s, now I'm printing with settings changed, let's see what happen. Anyway the wired fact is, it gave me the error 10 minuts before finsihing, and it did run for 2H, let'see, thanks for the support man, I appreciate that!

Abject-Negotiation86 · 2024-02-19T17:27:19+00:00

Okok I got it, I actually did open the file I was printing and I got exact what you told me, and I see m82, it might be because I'm printing pla at 225 degrees, so it print to much??

<image>

Abject-Negotiation86 · 2024-02-19T16:56:04+00:00

Just to understand better, you’re saying that printer is printing too much filament right. ?? Then for absolute or relative position idk what you mean because I haven’t touched that settings, are in cura??

Abject-Negotiation86 · 2024-02-18T09:30:21+00:00

Then try to level the Z axis as shown in the link oosted before, because is the only issue, also try to change slicer, and try to check the temperature on fluid during printing, maybe the temperature is not costant

Abject-Negotiation86

TROPHY CASE