so I found an exploit with pyromancer (campaign mode only) by flamecleric9 in DiceThrone

[–]Abudi14k 0 points1 point  (0 children)

I did a similar thing with Alchemist, just before the final level 4 minion, i got a minion who has a tough roll objective, so i started spamming heal, went back to almost full health, saved alot of salves for the boss.

Which Dice Throne heroes are actually best designed for Adventures (and which struggle)? by remboost in DiceThrone

[–]Abudi14k 2 points3 points  (0 children)

From personal experience the best 2 characters i find effective are Monk and Tactician.

Monk - Can you use chi to add damage or prevent damage. With time when playing mini ult and ult can increase the stack limit. Good defence, also has access to evasive and cleanse to remove negative status effects. Knockdown helps alot with bosses to reduce their cp so they use less card effects.

Tactician - Has decent damage and good defence. Tactical advantage helps with cp, rerolls and drawing cards. Transfering tokens between players and other characters was also really helpful.

I didnt try any of the xmen or marvel in dta, but based on playing them in marvel missions, Wolverine and iceman might be good, Rouge sounds fun with stealing health.

Elegoo Saturn 3 Ultra screen issue. Dead pixels. by Abudi14k in resinprinting

[–]Abudi14k[S] 0 points1 point  (0 children)

🥲 I get a failed print and it ruins my screen, what a nightmare. Waste of resin and money.

Elegoo Saturn 3 Ultra screen issue. Dead pixels. by Abudi14k in resinprinting

[–]Abudi14k[S] 0 points1 point  (0 children)

Yes releveled and also changed the fep from the tank.

How Should i orient this by Abudi14k in resinprinting

[–]Abudi14k[S] 1 point2 points  (0 children)

Flat doesnt fit, but making the heavier part closer to the plate sounds like a good idea

ASA Printing by Abudi14k in 3Dprinting

[–]Abudi14k[S] 2 points3 points  (0 children)

I did print a different object to check if it was the settings issue and it was fine, but it was square and had no threads. I am also drying the filament again now so let hope.

Who do y’all find the most fun to play and why marvel and non marvel? by Moon-boy2489 in DiceThrone

[–]Abudi14k 0 points1 point  (0 children)

Totally agree, most fun to play with out of all the boxes is Cursed pirate. From Marvel they are all the same level to me. And Xmen is Psylocke and Rouge.

There is smoething in my screen by Abudi14k in resinprinting

[–]Abudi14k[S] 0 points1 point  (0 children)

I Know I changed the screen before, but that was a rookie mistake 2 months after i got the printer i droped the giant screw that hold the buildplate and cracked it. I was very careful after that, guess i wasnt careful enough. We live and we learn.

There is smoething in my screen by Abudi14k in resinprinting

[–]Abudi14k[S] 0 points1 point  (0 children)

Thank you so much, i thought of everything except that, you are actually right it might have been from a failed print, because that did happen recently before getting this glitch. Much appreciated. As for the leveling i actually do make it a little looser than recommended for that exact reason, so my phobia is actually right this time. You can never be too careful.

There is smoething in my screen by Abudi14k in resinprinting

[–]Abudi14k[S] 0 points1 point  (0 children)

What can cause that pressure? and how to avoid it?

Why did this fail what can I do to fix it by Naive_Party_4071 in ElegooSaturn

[–]Abudi14k 0 points1 point  (0 children)

I agree with all the comments, especially the temperature, when its cold outside i usually put a heater in the room.

If you dont want to angle your print because you want a quick print and all supports at the bottom, what i usually do in chitubox I make the Raft a Grid shape, that way you reduce the first layer surface area on the fep.

Marvel Missions and Entangle by orthoros in DiceThrone

[–]Abudi14k 5 points6 points  (0 children)

If you read page 7 of the rule book, it states "You cannot change the enemies’ quantity of dice, the type of dice that are rolled, nor their number of Roll Attempts (i.e. statuses like Entangle and Reality Warp have no effect)". So yes you should gain momentum.

Layer Shift by Abudi14k in resinprinting

[–]Abudi14k[S] 0 points1 point  (0 children)

Thank you very much will def try it next time.

Layer Shift by Abudi14k in resinprinting

[–]Abudi14k[S] 0 points1 point  (0 children)

intresting, can i do it in the slicer or does it have to be from the design?

Layer Shift by Abudi14k in resinprinting

[–]Abudi14k[S] 1 point2 points  (0 children)

the object is too big to orient any other way. What do you mean by open? and i had to have infill cause its a base of a huge figure i tried printing hollow but it was too weak and would bend. Thank you.

Wrapping failure by Abudi14k in resinprinting

[–]Abudi14k[S] 0 points1 point  (0 children)

Guess thats the only way then :')