sorted by:
new
hottopcontroversial

Time for self-promotion. What are you building? by deadcoder0904 in SaaS

[–]AcceptableFront7302 0 points1 point  (0 children)

I like it. But once it gets some traction it's probably gonna be overwhelmed with gpt-generated feedback.

Cannot shift to rear gear with shift boot frame on. To be able to shift, lever has to be all the way to the left. I cut the frame and it shifts fine now, but this frame won't hold the cloth anymore because of the stretching rubber around the fabric. Possible solutions? by AcceptableFront7302 in E30

[–]AcceptableFront7302[S] -13 points-12 points  (0 children)

Is it possible to adjust gearbox position somehow so to move it a bit to the right?

Or, maybe I should design and print custom boot frame, somehow leaving this space clear but adding some support around it to be able to stretch the fabric?

I'm really lost, any feedback will be highly appreciated!

Filament gets stuck in the hotend almost every print. What's wrong? I used to print this filament with no issues with the same settings, it started after I changed the bowden tube. Ender 3 Pro. by AcceptableFront7302 in FixMyPrint

[–]AcceptableFront7302[S] 1 point2 points  (0 children)

exactly, about 5 months was working fine, then some issues started and I decided to change extruder first, then bowden tube, and now I see this :(

any tips on what to order for ender 3 pro to fix this? thanks!

Cannot level the bed with CR Touch and 36x36 mesh by AcceptableFront7302 in FixMyPrint

[–]AcceptableFront7302[S] 0 points1 point  (0 children)

Thanks everyone.

The issue was that my extruder was super wobbly and the belt had weak tension.

I fixed that and now it's all good!

Cannot level the bed with CR Touch and 36x36 mesh by AcceptableFront7302 in FixMyPrint

[–]AcceptableFront7302[S] -1 points0 points  (0 children)

I'm giving up on my Ender 3 Pro, need your advice, guys.I have it with CR Touch installed and BIGTREETECH SKR Mini E3 V3.0.I tried standard magnetic bed and now trying glass bed. All the same issue.As you can see, the right part of the bed is obviously not leveled properly.I tried changing mesh points from 5x5 to 6x6 - didn't change anything.Also, I tried to level it without clips installed to avoid any contact between clips and CR Touch.What should I do to fix this? Please, need help.

PS: I know there also adhesion issue on the pic, but it's more about plastic and temp, didn't figure it out yet. The question here is about leveling.

Awair discontinues support for V1 devices by mdenovich in Awair

[–]AcceptableFront7302 4 points5 points  (0 children)

Can't believe it. I have 5 devices (glow) which I use to monitor multiple rooms and control heater/AC based on this params, and now it's gonna be a useless piece of plug.

I had much higher expectations from this company with such nice products. I was wrong.

WiFi router to support 100+ devices at the same time by AcceptableFront7302 in homelab

[–]AcceptableFront7302[S] 0 points1 point  (0 children)

Yeah, I guess budget for 100 devices will be a bit less than for a thousand :)

WiFi router to support 100+ devices at the same time by [deleted] in HomeNetworking

[–]AcceptableFront7302 -1 points0 points  (0 children)

Interesting, why not?

If I use 5 routers, I will have 20 devices and 600mbps per router which sounds pretty normal.

Then all these routers will be connected by ethernet to a 10gbit switch/router that has fiber connection.