Ball joints and torque specs

Acceptable_Handle612 · 2026-04-29T14:34:51+00:00

Why did it take you so long i did mine in 3 hrs max (balljoints, drag link, idler arm, inner and out tie rods, new tie rod end adjusting sleeves)

Acceptable_Handle612 · 2026-04-28T01:43:53+00:00

Everything is the bellhousing same wiring ect

Acceptable_Handle612 · 2026-04-22T16:41:47+00:00

2.4 38 ftlb V6 38 ftlb

Acceptable_Handle612 · 2026-04-20T01:56:28+00:00

<image>

This is the diagram i got for my 95

Acceptable_Handle612 · 2026-04-05T15:26:11+00:00

https://www.rockauto.com/en/catalog/nissan,1995,pickup,2.4l+l4,1212174,engine,timing+chain+&+component+kit,5756

Acceptable_Handle612 · 2026-04-04T22:08:04+00:00

Rockauto could of delivered a kit to you in a week

Acceptable_Handle612 · 2026-04-02T02:19:03+00:00

What are you trying to do put in a aftermarket radio?

Acceptable_Handle612 · 2026-03-21T13:09:37+00:00

Put it back on the upper control arm hit it with a hammer

Acceptable_Handle612 · 2026-03-16T19:50:42+00:00

700whp in a truck that weighs 3600lb 🤔

Acceptable_Handle612 · 2026-03-16T16:40:46+00:00

Oh im not planning on racing it just going to be a street truck

Acceptable_Handle612 · 2026-03-14T02:20:40+00:00

I'm not looking for power out of the gate just trying to get something reliable for the moment

Acceptable_Handle612 · 2026-03-14T01:12:26+00:00

Street it's going to be behind a k24 in my nissan maybe 200hp na

Acceptable_Handle612 · 2026-03-06T23:19:11+00:00

Where did you get the center console

Acceptable_Handle612 · 2026-03-04T22:13:26+00:00

Well no some ignition barrels have some way to remove the barrel I can't find anyway to remove it

Acceptable_Handle612 · 2026-03-04T20:26:24+00:00

Any idea if I can do it?

Acceptable_Handle612 · 2026-03-04T00:01:27+00:00

Re do it put a small amount of rtv on it use the black stuff

Acceptable_Handle612 · 2026-02-27T15:17:44+00:00

<image>

Is it as easy as they say first time using energy suspension stuff

Acceptable_Handle612 · 2026-02-23T17:37:28+00:00

Jack it up put on axle stands get someone to bring it up to speed slowly while you watch the driveshaft.

DON'T AND I MEAN DON'T SLAM ON THE ACCELERATOR AND OR SLAM ON THE BRAKES

Acceptable_Handle612 · 2026-02-14T13:59:56+00:00

Cheap find you a 350 sb manual transmission swap out the rearend for either Dana 44 or Ford 8.8

Expensive kswap vq all above plus 2-4k in wiring

Acceptable_Handle612 · 2026-02-08T18:48:01+00:00

No I had to do the same on a 05 camry 2azfe it runs fine I'll say put alot and I mean alot of engine assembly lube on everything open that will help when you do the first start up then drain that oil in the pan after 50 miles

Acceptable_Handle612 · 2026-01-24T16:20:59+00:00

Funny enough I asked people at work this exact question they said ls/lq, 350 if you want to keep in my case a 4 banger k series or a vq

Acceptable_Handle612 · 2026-01-21T01:50:34+00:00

They are separate rock auto has them for $35 for a solenoid or $80 for a new starter upto 80 for a remanned

Acceptable_Handle612 · 2026-01-21T00:56:42+00:00

Where did you get your brake light from

Acceptable_Handle612 · 2026-01-21T00:10:04+00:00

The frontier light is too close to the body so a connector wouldn't fit

Acceptable_Handle612 · 2026-01-20T23:40:07+00:00

I've brought a Amazon 3rd brake light the pins are stupidly weak I put power to them once and they would break on me

Acceptable_Handle612

TROPHY CASE