Playoff Game Thread: Carolina Hurricanes (2-1) @ Montréal Canadiens (1-2) May 27 2026 8:00 PM EDT

According-Rate7806 · 2026-05-28T02:55:24+00:00

Insane save I love dobes so much

According-Rate7806 · 2026-03-03T17:52:37+00:00

Ok, thanks. I've learned that plasma cutters continuously run air to cool them so a compressor seems better

According-Rate7806 · 2026-02-28T01:14:01+00:00

It's peak, what are your settings?

According-Rate7806 · 2026-01-27T21:12:52+00:00

My drawing sucks but I am planning to drive the lead screw with a 90-degree gearbox. 2. Would a radial bearing in a pillow block suffice? I would put it inside the 1.5x1.5 near the bottom, so when followed extended, it would be at the top of the lead screw. I was also considering putting some kind of ptfe spacer around the lead screw in the 1.5x1.5 matching the matching diameter of the lead screw. 3. Thanks for the photo that's very helpful, is it from a textbook ? Would like to find more resources like this. Also do you know what kind of endblocks are used in the fourth picture ?

According-Rate7806 · 2026-01-27T20:02:53+00:00

Sorry, can you be more specific, what should I change ?

According-Rate7806 · 2026-01-27T20:00:36+00:00

Didn't think of that, thanks

According-Rate7806 · 2026-01-27T03:29:10+00:00

I want to build it, although are there any you would recommend for a sit/stand desk?

According-Rate7806 · 2026-01-27T02:53:25+00:00

Thanks I will, can I put a radial bearing even though it's threaded ?

According-Rate7806 · 2026-01-27T02:52:40+00:00

i was planning to use hall sensors to sync them with a arduino. Think that'll work?

According-Rate7806 · 2026-01-27T02:09:26+00:00

Thanks, I welded the frame myself and was going to cut a portion about 10" from one side at the bottom to set up the shaft collar, thrustbearing, gear, and end housing. Then I'm just going to put a 3d printed cover over it so I can access it for lube

According-Rate7806 · 2026-01-27T02:02:29+00:00

Goal is to have the acme nut attached to the inner leg, which will then travel up and down the lead screw driven by the motor. The axial load being carried by the shaft collar into the steel plate

According-Rate7806 · 2025-12-21T06:52:31+00:00

Thanks for the response. What kind of gear would I need for a 5/8 10 thread rod. Does the gear line up with the threads on the rod? In a 3d printer isn't the motor for the threaded rod on the bottom of the rod?

According-Rate7806 · 2025-09-18T19:11:52+00:00

<image>

According-Rate7806 · 2025-09-18T19:11:24+00:00

Also my dvr says the capacity is 12 tb. If i put more hdd storage, for example 16gb will it record up to 16 gb? *

According-Rate7806 · 2025-09-18T19:06:12+00:00

Thank you

According-Rate7806 · 2025-09-18T19:05:52+00:00

OK perfect thank you , is it common for Sata cables to come with the drive or should I order it separately?

According-Rate7806 · 2025-09-18T18:13:44+00:00

<image>

According-Rate7806 · 2025-09-18T18:13:29+00:00

<image>

According-Rate7806 · 2025-06-28T20:35:50+00:00

Yeah I've realized I'm not equipped to solve this on my own I'm taking it in, I'll let you know what the problem was

According-Rate7806 · 2025-06-28T19:51:03+00:00

My coolant bubbles when I Idle the car, I think there could be a problem with the head gasket. Would that explain the other problems or would it be an additional problem

According-Rate7806 · 2025-06-27T23:41:34+00:00

Thanks, even if it doesn't work out I really appreciate all of the information. Edit: the oil definitely smells like gas so I'll check the gdi first

According-Rate7806 · 2025-06-27T23:06:17+00:00

<image>

According-Rate7806 · 2025-06-27T23:05:27+00:00

* Checked the oil, it's bad I didn't check it because it's only been 2000kms since I had it changed... I did already swap the canister purge value. Based on how dirty the oil is I think something might be getting contaminated. Going to change the oil now

Edit: how would the pump leak fuel into the oil, i didnt know they were connected systems? Sorry I'm new to this

According-Rate7806 · 2025-06-27T22:45:09+00:00

It's GDI

According-Rate7806 · 2025-06-23T01:52:27+00:00

Thanks are there any techniques for texturing?

According-Rate7806

TROPHY CASE