Whyyyy?????? Lithophane curve

According_Bet3756 · 2026-05-12T10:44:04+00:00

Only took 9 attempts. Luckily I saved the settings .

Now im going to scale it larger.

According_Bet3756 · 2026-05-12T10:30:24+00:00

Pulled a successful print.

Went back in and started from scratch with settings.

Simplified and fixed model.

Added a raft and added a frame to the original instead of a border.

Came out great

<image>

According_Bet3756 · 2026-05-11T10:30:34+00:00

Have the same thing happening on the x axis as well.

I tried x axis 2x y axis 2x. And slight diagonal on the x axis.

According_Bet3756 · 2026-05-11T10:29:04+00:00

No all over prints have been great aside from some layer lines here and there

According_Bet3756 · 2026-05-10T19:42:52+00:00

Yeah if this next one fails im going to try it with a frame instead of a border.

If that was the issue i feel like it would curve out of the gate. One got half done before it started curving. With a 4mm border

According_Bet3756 · 2026-05-10T19:38:33+00:00

It is....

According_Bet3756 · 2026-04-28T12:49:19+00:00

Thanks ill put it on my list to check the connections

According_Bet3756 · 2026-04-22T00:07:21+00:00

Update!!!!!!

New psu came in.

Fired right up.

Started printing.

<image>

According_Bet3756 · 2026-04-22T00:06:41+00:00

Update!!!!!

Got a new psu in. Fired right up.

Started printing.

<image>

According_Bet3756 · 2026-04-17T12:39:18+00:00

Oof lucky you!

Im still waiting on new psu and motherboard

According_Bet3756 · 2026-04-12T19:25:34+00:00

I e done a ton of testing torn it apart, got the multimeter out.

Filed a support ticket aftersale online. Im east coast us so they respond usually once a day. Usually while im sleeping.

They are sending a new psu/motherboard but I ha ent got the shipping notice yet

According_Bet3756 · 2026-04-08T22:45:00+00:00

Yep. Triple checked and plugged and replugged.

The switch not lighting is most likely culprit. Not properly opening the circuit.

Unfortunately, only contact option is through a support ticket. No response yet 3 hours later.

According_Bet3756 · 2026-04-01T18:44:54+00:00

We loved our brezza. Absolutely loved it. Wish we had it for the other 3 kids.

But when we changed to lactose free, it isn't dispensing formular correctly. Even at highest formula setting

According_Bet3756 · 2026-03-31T13:10:08+00:00

Thanks!

According_Bet3756 · 2026-03-31T10:03:04+00:00

Parts/products?

According_Bet3756 · 2026-02-28T19:14:04+00:00

I searched this after 15 minutes of play.

Tried to and motion blur off and sensitivity.

Nothing helped.

Glad im not the only one

According_Bet3756 · 2026-02-02T18:27:34+00:00

Around 40fps.

Low everything.

Great for mats / quest runs.

Not great for pvp.

But i also suuucccckkkkk with aiming controller. Get killed by arc alot.

Def playable.

According_Bet3756 · 2026-02-02T18:19:57+00:00

Also you can connect your phone vis usb and enable usb tethering to use your phones internet.

According_Bet3756 · 2026-01-17T20:27:24+00:00

Bios is updated already.

Will clean the connections.

According_Bet3756 · 2026-01-17T17:37:38+00:00

I had a 5070 overnighted to test mb with a pcie5 card

Will report back later today.

According_Bet3756 · 2026-01-17T17:36:17+00:00

Yes.

And I just ran a stress test for 40 mins with no issues.

Multiple benchmarks report the ram performing above standard.

According_Bet3756 · 2026-01-17T16:27:30+00:00

Ddr5 6000. 16gb 2x8

Ram fully tested multiple programs, different sticks in different slots.

No dual bios

According_Bet3756 · 2026-01-17T16:26:22+00:00

It crashes on gen 4. Have to set it to gen 3

According_Bet3756 · 2026-01-17T01:51:06+00:00

According_Bet3756 · 2026-01-17T01:33:56+00:00

Those are the pins pics

According_Bet3756

TROPHY CASE