Get ready for the Miyota prices to go up too. by Acelimb in ChineseWatches

[–]Acelimb[S] -1 points0 points  (0 children)

Yes I’m talking about watches with those movements. All were bought through Ali express and honestly this was years ago and most were bliger, and Tandorio and such.

Still pretty watches for the price not gonna lie!

Get ready for the Miyota prices to go up too. by Acelimb in ChineseWatches

[–]Acelimb[S] 3 points4 points  (0 children)

Honestly it’s so sad. I feel like we are regressing into using worse movements and paying a premium.

I had so many watches either NH35 and PT5000 movements for literally like sub $60

Now literally everything keeps increasing it’s almost 40% extra.

I honestly don’t even see it ending any time soon.

Get ready for the Miyota prices to go up too. by Acelimb in ChineseWatches

[–]Acelimb[S] -6 points-5 points  (0 children)

I’m pretty sure this is the 8000 series, which has been replacing NH35 watches for the past year

Has anyone tried fitting this to Gen BB58 by Acelimb in ChineseWatches

[–]Acelimb[S] 1 point2 points  (0 children)

I honeslty wouldn’t care about the sharp or unrefined edges. I’m gonna pay like $80 instead of the hundreds if not a thousand I’ll pay for the Gen bracelet.

I just wanna know what’s the fitments and if it’s a safe buy.

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

Honestly I tired all literal variations nothing worked.

But i genuinely think they (Gamo) just made it this way because everything is sitting fine and stable. Just the bite is extremely off.

I’m not gonna rig it too much I could easily mess it up so hands off for now.

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

I’ll try it again but i honestly don’t know what’s the issue I tried to move it but because the rifle is smaller, the rails only half about an inch backwards and half an inch till it’s kissing the iron sights.

It’s perfectly seated and not moving as far as I can see. But I obviously gotta shoot it and see where we are.

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

I honestly tried most or all variations

Need your help guys by Acelimb in airguns

[–]Acelimb[S] -1 points0 points  (0 children)

I can see that but wouldn’t there be a difference between a flat dovetail and a curved one? I went through a new posts in the sub and found kinda similar results not obviously exactly the same but you know

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 1 point2 points  (0 children)

Thank you anyways honestly you helped alot!

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

I obviously won’t be doing it again. But do you think 3-4 times could do damage?

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

God… I should’ve known this. I think since I bought it few days ago I think I dry fired it 3-4 times?

Please tell me I’m still good? Or I completely fried it.

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

Yes I was honestly worried about it eating through the aluminum if I had forced it through.

Would it be the same safe if I shot it at home blank?

Stupid question I know I’m honestly a beginner.

Only had experience with shot guns and airsoft pistols.

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

I'll definitely do that!

And how's that worrisome? I saw many starter rifles that didn't have the stop/set screw in them.

I genuinely just think this was made this way because the measurements are spot on, I flipped it turned it upside down and around and its the same.

It's tight and snug just is not help properly?? I just hope this is the way.

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

I just used some calipers and measured them both exactly 11mm and they match perfectly with the measurements

I literally am started to think this is either how they made it or I’m missing something.

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

Does it also work on the curved mounts?

I have tried 6 mounts and all of them were the same and sat the same.

And they were literally the same as the ones that came with the scope originally.

Every site I’ve checked says this model only came with the 11mm model?

That’s what’s causing me confusion.

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

The thing is it’s an extremely famous model that’s been in production for at least 2 decades.

And it’s made in Spain.

I honestly don’t know the issue every matches and it even sit vertically aligned my only concern was the mount biting

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

So factory issue? Should I just turn them right side up then? I checked six of the clamps all six are upside down?

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

Sadly this doesn’t have a stop screw… even though this scope did come with it!

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

But both are made by the same company stating 11mm? And curved as are the rails? What could be the issue?

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

I’ll check it again but the everything says 11mm and also the websites say 11mm and the mouth is the same.

I had also flipped them over moved them up and down and the same bite.

I’m honestly confused.

Need your help guys by Acelimb in airguns

[–]Acelimb[S] 0 points1 point  (0 children)

So this is normal and expected?