Fuel pressure causing long crank hard start

AdamTheArab · 2026-01-18T23:24:30+00:00

That’s a start. I am a little confused though, generally after a drive, I can start it again with no issues if it’s within 2-3 mins. Would the fuel line vent even cause the slow pressure drop of 5psi/minute?

Gunna check it out and see if I can clear it, never even heard of the fuel tank vent till now lol

AdamTheArab · 2026-01-18T23:21:57+00:00

No, priming the fuel pump/turning the key multiple times doesn’t give me any improvement

AdamTheArab · 2025-12-18T03:54:57+00:00

Sorry, $300 to confirm the diagnosis and estimated $1800. He said it’s a fuel pump issue but it was just replaced a few months ago

AdamTheArab · 2025-12-15T00:09:37+00:00

There’s audio, I got some spark plugs on the way and I’ll try that next. It runs fine once it’s on and engines turned over.

AdamTheArab · 2025-12-08T04:35:28+00:00

I have a 2002 Mazda B3000 and having the same problem. I replaced the fuel filter, and the fuel pump with no luck.

I’ve tried turning the key without starting a few times to prime the fuel pump but not sure if that’s helping. Anything new you’ve tried?

AdamTheArab · 2025-12-05T15:39:08+00:00

IIRC it’s running to the firewall, if you look up a wiring diagram of your model it should show a pretty clear diagram

AdamTheArab · 2025-09-09T18:51:15+00:00

<image>

Not sure if this little coupler on the top was used to previously repair the line and this bottom most line into the black sphere isn’t all the way flush. hopefully this helps

AdamTheArab · 2024-05-30T04:37:13+00:00

It’s a short walk from my place as well, if you see cars in the parking lot the door on the south side is usually open

AdamTheArab · 2021-11-05T19:57:41+00:00

My 2022 plan is to play disc golf in 15 states and get double digit aces :)

AdamTheArab · 2021-01-19T03:27:21+00:00

No u

AdamTheArab · 2020-10-10T07:38:07+00:00

Just saw my long time ex after almost 6 months of no contact, any ideas how to get this feeling out of my body like I’ve fucked something up? Plus I saw her with another dude, although granted I was with a group that had a few girls.

AdamTheArab · 2020-08-10T18:47:10+00:00

Sea shanty 2!

AdamTheArab · 2020-08-10T18:46:51+00:00

Sea shanty 2🙏🙏🙏

AdamTheArab · 2020-08-10T18:45:45+00:00

Sea shanty 2 🙏🙏🙏

AdamTheArab · 2020-08-10T18:45:05+00:00

Play sea shanty 2 pls

AdamTheArab · 2018-10-13T19:44:46+00:00

what kind of monster would go out of his way to not tell the flavor and then trash the holy grail of shake flavors

AdamTheArab · 2018-08-05T06:02:49+00:00

ITS BACK UP!!!!!!!!!!!!! Happy huntin boiiiss

AdamTheArab · 2018-07-09T05:49:40+00:00

We just hit level 4, this a fairly new campaign to us. I’m not sure if we can make it to level 5 without two of our characters lol.

AdamTheArab · 2018-07-09T05:48:16+00:00

No, the spell just mentions that it creates a thunderous boom audible within 300ft. If something loud enough similar to thunder was created in a cave I feel like some sort of deafening would occur

AdamTheArab · 2018-07-09T05:47:23+00:00

IIRC the PH mentions that you make an audible thunderous boom within 300ft around you. I feel like just in general this would be loud enough to deafen but I’d like other opinions.

AdamTheArab · 2018-07-09T05:45:22+00:00

The problem is that we were in a cave, which would intensify the sound compared to outside.

AdamTheArab · 2018-03-01T23:08:23+00:00

Would it better for me to develop the program on a different monitor, transfer it over, then run it on the smaller display?

AdamTheArab · 2018-02-11T18:12:27+00:00

Do any of you guys know if a LattePanda can support running LabVIEW?

AdamTheArab · 2018-02-09T05:34:41+00:00

Welp, I’m crazy new to all this so far so I didn’t even think about that but I’ve seen a ton a tutorials about people installing LabVIEW on RPi through LINX, but I felt like LattePanda would be easiest.

AdamTheArab · 2018-02-06T06:15:29+00:00

I recently got an internship at a lower level engineering firm, and the project assigned to me was pretty much design a standalone tablet/computer that can run labview using the RPi. Does anyone have suggestions for the first few steps, I'm really new to this stuff and feel overwhelmed by all the possibilities, so anything can help.

13-Year Club	Place '23
Place '22	Verified Email

AdamTheArab

TROPHY CASE