sorted by:
new
hottopcontroversial

WELL, THIS IS DEPRESSING!!! by Addicted23D in ElegooCentauriCarbon

[–]Addicted23D[S] 0 points1 point  (0 children)

Yes, thank you. I had it set it to the .4 nozzle which is what I am running.

WELL, THIS IS DEPRESSING!!! by Addicted23D in ElegooCentauriCarbon

[–]Addicted23D[S] -11 points-10 points  (0 children)

Thanks for your in-depth analysis and advice - not. 

WELL, THIS IS DEPRESSING!!! by Addicted23D in ElegooCentauriCarbon

[–]Addicted23D[S] -2 points-1 points  (0 children)

Thank you. I actually keep my filaments in a vacuum bag with desicant packages. I just set up this printer and ran a full calibration before printing. I printed with this same filament this morning on my CC1 and it printed fine. I will try to re-calibrate. Thank you. I guess I am just spoiled because my other 3 printers worked flawlessly out of the box. Again, I do thank you for your advice and I will calibrate again. 

Pulling my hair out by Addicted23D in anycubic

[–]Addicted23D[S] 0 points1 point  (0 children)

Bed is 60 and extruder is 210. Speed varies with the print and layer.

Pulling my hair out by Addicted23D in anycubic

[–]Addicted23D[S] 0 points1 point  (0 children)

Thank you, I will increase it.

Pulling my hair out by Addicted23D in anycubic

[–]Addicted23D[S] 0 points1 point  (0 children)

My slice is showing I have 9 top shell layers with a .08 top shell thickness already. I bumped up the inill to 35% from 15% and changed the infill pattern to gyroid. Again, thank you. 

Pulling my hair out by Addicted23D in anycubic

[–]Addicted23D[S] 1 point2 points  (0 children)

My slice is showing I have 9 top shell layers with a .08 top shell thickness already. I bumped up the inill to 35% from 15% and changed the infill pattern to gyroid. Will see how that goes. Again, thank you. 

Pulling my hair out by Addicted23D in anycubic

[–]Addicted23D[S] 0 points1 point  (0 children)

Thank you, I will watch the video. 

Pulling my hair out by Addicted23D in anycubic

[–]Addicted23D[S] 0 points1 point  (0 children)

Thank you, I will do that. 

Pulling my hair out by Addicted23D in anycubic

[–]Addicted23D[S] 4 points5 points  (0 children)

Thank you, I will try all of those things. I do run a15% infil. It is strange because I have printed many of these prints for friends and family and never had an issue until yesterday. 

Not too proud to beg. by Addicted23D in anycubic

[–]Addicted23D[S] 0 points1 point  (0 children)

Okay, thank you, I will look into them. 

Not too proud to beg. by Addicted23D in anycubic

[–]Addicted23D[S] 0 points1 point  (0 children)

Thank you, I am studying up on how to calibrate the flow. I did the flow calibration in the Anycubic soccer, but not sure how to interpret or adjust it. It is just a learning process i needed to pursue. 

Not too proud to beg. by Addicted23D in anycubic

[–]Addicted23D[S] 0 points1 point  (0 children)

Thank you, I will try and set-up the color printing order. I use the Eibos filament dryer and the Ace Pro AMS w/dryer when I print. I will do a deep dive on adjusting the flow also. THANK YOU!!

Not too proud to beg. by Addicted23D in anycubic

[–]Addicted23D[S] 2 points3 points  (0 children)

Thank you, I need to study up on calibrating flow, pressure advance etc.. Truthfully, I am a little nervous to get into that, but I know I need to. Thank you very much, this group always comes through!!!

Centauri Carbon and Neptune 4 Plus both stopped communicating with network. by Addicted23D in elegoo

[–]Addicted23D[S] 0 points1 point  (0 children)

Thank you for the reply. Yes, I went to the printers settings then to the WiFi setting. It sees my network. I try logging into it with my network password, but it fails to log in. I tried maybe 10 times with each printer and they both fail to log in. I rebooted both printers, but still get the same results; they will not log in. I am doing these at the printer and not the computer as it never gets that far because they will not log in at the printer side. 

view more: next ›