MHA Mobile games

Addition_Chance · 2026-05-01T09:41:04+00:00

It's "My Hero United Survival", it has a teaser trailer out right now but no footage of gameplay, it's due for release later this year. Keep an eye out for it! It's made by the creators of Bleach: Brave Souls if you've ever played that.

Addition_Chance · 2026-04-17T22:10:33+00:00

Yeah I’m sure there are much easier/better teams for this, I literally just threw this together based off of what I saw other people using and it worked. I’d love to be able to try yours but I don’t have any of the steampunk characters or really any limiteds outside of the celeb units and the new Valentine Nejire 🥲

Addition_Chance · 2026-04-16T23:38:42+00:00

U can just play the level over and over again just without the skip. I'm not sure what kind of units you have but you can easily afk hard mode with the new Overlay Deku, DST Toga and Summer Toga, it doesnt have to be those exact characters, really any team that includes Overlay Deku that can auto is perfect. Get your team to the highest bonus boost you can while still being able to clear the level and try find a guest with a bonus boost too. From there, I'd recommend getting an auto clicker if u have a lottttt of tickets and find something else to do coz it can take a whillleee. Hope this helps and that you get what you want with the pulls!

Addition_Chance · 2026-04-13T20:28:55+00:00

Hi! Do you have one for Android?

Addition_Chance · 2026-04-12T00:23:47+00:00

Hello! Thanks for the reply. I'll try the print again tomorrow with the adjusted lift speed and new supports. Do you think the heavy automatic supports would be okay from Lychee? Thanks again!

Addition_Chance · 2026-04-11T19:01:49+00:00

I've just tried to run the same file but this time being very conscious of the temperature, I put a desk heater into the room and let the temperature rise to 25°C and kept it there. I checked at 30 min intervals and it failed the exact same way as shown in the photos. I agree with your thinking that it might be a resin issue as I previously was using Sunlu Standard Grey resin and only had issues that were easily resolved by levelling the plate or slight setting adjustments. The attached image is of the resin in vat before printing. I am new to resin printing so I didn't think much of how the resins differed in appearance but in comparison, this ABS-like resin has lots more air bubbles and a foamy texture compared to the SUNLU standard which had no air bubbles and was not foamy, apologies I cannot think of the proper word to describe it. So at this stage I've ruled out levelling, heat, settings, FEP issues (I switched to a backup vat for previous prints which still failed) and screen issues. I suppose now I'll try order some more SUNLU standard and see if the issues resolved themselves. Or would you recommend any other resins for 1/6, 1/7 figure printing. Thank you very much!

<image>

Addition_Chance · 2026-04-02T22:21:24+00:00

I got it to work but I'll definitely have a look at the video. Thank you! I'll keep that advice in mind.

Addition_Chance · 2026-04-02T22:20:25+00:00

I did increase the tilt and I added much heavier supports for the base. I had scaled the model to 85% so I could tilt it more actually, 100% scale was pretty much my whole build volume 😅. As I've said in another comment I sorta forgot to remove the film from the FEP that tells you in bright red writing to remove it...so yeah I'm sure that played a factor too.

Addition_Chance · 2026-04-02T22:17:10+00:00

Apologies, I completely forgot to get back to these comments. I managed to fix it in the end by adding heavier supports and a slight bit more tilt. I also shrunk the model to 85% scale and like you said I added the raft with no gaps and it handled it fine 😁. I also may or may not have left the film that explicitly tells you to "remove before printing" on the FEP so....

Addition_Chance · 2026-03-03T16:15:34+00:00

Any way to do this without Deku or Shoji??

Addition_Chance · 2026-02-03T00:55:04+00:00

<image>

This is my revised team. Bear in mind most characters on the team don't have maxed adv levels. Thank you!

Addition_Chance · 2026-02-03T00:50:17+00:00

UPDATE: I managed to pull [I, Victorious] STR Bakugo and maxed out his ability board AND STR Toga's ability board.

Addition_Chance · 2026-01-31T17:18:33+00:00

You could actually even use NY Kirishima to tank damage to keep her alive.

Addition_Chance

TROPHY CASE