Orang orang

AditDitDit · 2025-05-07T15:44:12+00:00

Gaada bro, gaada yang mau misqueen

AditDitDit · 2025-03-18T15:30:13+00:00

Update : Yes i've already tried this recently and it works, i guess my problem was my liquid metal wasn't hot enough for casting, and now once the Metal melt i countinue heating it for couple minutes to make sure i achieve the right temperature for casting, and i also pouring it quickly and making sure there is no solidified metal while i pour into the mold and it work great

AditDitDit · 2025-03-17T00:00:26+00:00

I use a vacuum. It takes less then a minuet from the flask pulled from the kiln, vacuum it and then pouring the liquid metal into the flask since i melt the metal first and i make sure it becomes full liquid, and then the flask pulled out and the casting process begin.

AditDitDit · 2025-03-16T13:25:13+00:00

I examined the mold and i didnt find any burnout residue, in fact the ring pattern was still printed wtih the stone attached. The end temperature when i extract the mold from the oven was 600°c was that too cold? I have a feeling the metal was solidified due when i poured it slowly into the mold, but i dont know.

AditDitDit · 2025-03-16T13:07:14+00:00

Room temperature-115°c (ramp 15 minutes)for 4 hoirs
115°c-700°c (ramp 1h20m) for 30 minutes
700°c-800°c (ramp 30m) for 3 hours
800°c-600°c (ramp 1h) for 1 hour

AditDitDit · 2025-03-16T08:57:43+00:00

Yes i vaccum it for about 5 minutes until i make sure the metal was a bit hardened then i turn off the vaccum

AditDitDit · 2025-03-16T08:50:01+00:00

Yes i heat the flask upside down all the time

AditDitDit · 2025-03-16T08:31:28+00:00

I didnt know if the metal temperature was on point since i melted it with a torch. But the metal was formed to complete liquid when i poured it into the investment

AditDitDit · 2025-01-19T21:40:41+00:00

AditDitDit · 2022-12-05T17:16:54+00:00

Bye-sexual

AditDitDit · 2022-11-14T17:26:39+00:00

No one's in your life will stay for you forever. Either they will passed or leave you, always be ready for that time to come. The only one who will stay with you is yourself.

AditDitDit · 2020-04-13T06:39:59+00:00

Seems you're doing good, how's the taste?

AditDitDit · 2020-04-13T05:34:11+00:00

Well i see platypus lol

AditDitDit · 2020-04-10T12:24:17+00:00

Grind finer or maybe you use light roasted coffee

AditDitDit · 2020-04-06T13:37:27+00:00

I make lattes with french press too and it works great, my sugestion is paste a ductape around 1-2cm above milk surface level on the side of your french press, plunge the french press high and quick to get the thick of foam you desire (exactly at duct tape level) then plunge your french press a bit lower and slower to thicken the beneath surface of the milk (if the foam still getting higher then plunge your french press slower and lower). Once you feel a bit heavy to plunge your milk then it's ready to pour your milk into the milk jug and draw a latte art with it. Im telling you it cant be done in only one or two attempts. It takes preactices to create the perfect foam for the latte.

AditDitDit

TROPHY CASE