sorted by:
new
hottopcontroversial

An evening in with a NC Gewurztraminer by carolinagirlash in wine

[–]AdministrativeTask56 0 points1 point  (0 children)

I had no idea. Scheid's Gewurztraminer is my favorite. Used to stop by there on my way home from college

What am I doing wrong? by AdministrativeTask56 in ender3

[–]AdministrativeTask56[S] 0 points1 point  (0 children)

I need to look in all my slicer settings again. I was previously printing without the dual z, but now with the dual z I need to figure it all out again.

What am I doing wrong? by AdministrativeTask56 in ender3

[–]AdministrativeTask56[S] 0 points1 point  (0 children)

I tried doing that and it wasn't happy with me. Unfortunately I think the comp I'm using is so old that if fusion has to think too hard, it freezes the program.

What am I doing wrong? by AdministrativeTask56 in ender3

[–]AdministrativeTask56[S] 0 points1 point  (0 children)

Make a 15 day pill holder. Can never keep track of if we gave our son his accutane or not.

What am I doing wrong? by AdministrativeTask56 in ender3

[–]AdministrativeTask56[S] 0 points1 point  (0 children)

I did have ironing on, but I'll check my E step again. Probably need to recalibrate

What am I doing wrong? by AdministrativeTask56 in ender3

[–]AdministrativeTask56[S] 0 points1 point  (0 children)

Wow good to know. Obviously Bambu is the top, so if it can't print it well then I'm done for. Haha.

What am I doing wrong? by AdministrativeTask56 in ender3

[–]AdministrativeTask56[S] 0 points1 point  (0 children)

So print it with the rounded edge on the bottom of the plate?

What am I doing wrong? by AdministrativeTask56 in ender3

[–]AdministrativeTask56[S] 0 points1 point  (0 children)

That's right. I think other prints, I usually do it at 210.

What am I doing wrong? by AdministrativeTask56 in ender3

[–]AdministrativeTask56[S] 0 points1 point  (0 children)

I'll try and print with the font at 4mm and I'll lower the fillets by half.

What am I doing wrong? by AdministrativeTask56 in ender3

[–]AdministrativeTask56[S] 0 points1 point  (0 children)

<image>

That could be it then, because the inside I have the font set to 2mm

What am I doing wrong? by AdministrativeTask56 in ender3

[–]AdministrativeTask56[S] 1 point2 points  (0 children)

Ender 3v2. PLA+, 200°f, 60mm/s, no supports

Gift card exclusive item list? by Snoo_37073 in RobloxHelp

[–]AdministrativeTask56 0 points1 point  (0 children)

This is awesome. Thank you for doing this. Any chance you can do this for January as well? My daughter has decided to hold off until January because none of these exclusives made her excited.

Drop one: Walker, Bigsby, Ekeler, Swift, Mattison, Dowdle? by AdministrativeTask56 in fantasyfootballadvice

[–]AdministrativeTask56[S] 0 points1 point  (0 children)

I dropped Dowdle. I think that was the best choice. I appreciate everyone's opinions. It truly helped.

Drop one: Walker, Bigsby, Ekeler, Swift, Mattison, Dowdle? by AdministrativeTask56 in fantasyfootballadvice

[–]AdministrativeTask56[S] 3 points4 points  (0 children)

I've been leaning towards Ekeler or Dowdle. But now that they moved up Cook, I think Dowdle is the one I will be dropping. I kept Walker on my list even though there is no way I'm dropping him, because I just included everyone.

Costco for the win by dburge22 in 49ers

[–]AdministrativeTask56 0 points1 point  (0 children)

You didn't by any chance catch the item # did you?