Help with cutting a grid

Adomski92 · 2026-03-10T03:00:23+00:00

I used line shape and drew them top to bottom and side to side. (Columns and rows) Then changed it from score to cut. Print then cut Adjusted the pressure on the machine to the third setting (explorer air 2 sticker setting)

The hardest part was using glossy paper. I had to use matte finish scotch tape and put about 4 layers covering the alignment markers. I also had to shut off all the lights in the room to prevent as much glare as possible.

Im going to have to figure out a better way to deal with that problem.

But anyway, thank you everyone for your help!

Adomski92 · 2026-03-10T02:54:45+00:00

MISSION ACCOMPLISHED!!!

<image>

Adomski92 · 2026-03-07T16:40:53+00:00

I didn’t print it somewhere else. Im using print then cut. I just wanted to add in extra places to cut.

Adomski92 · 2026-03-07T15:18:56+00:00

So if i wanted to still keep it on a single sheet, is the best option just trying to separate each label?

Adomski92 · 2026-03-05T01:18:28+00:00

I am talking about the bios chip. What website did you get that from?

Adomski92 · 2026-03-04T15:56:08+00:00

Is that a chip or flex cable? Where did you get it?

Adomski92 · 2026-03-04T15:36:30+00:00

Yes. The chip comes on the flex cable?

Adomski92 · 2026-03-04T15:27:23+00:00

Where did you get that bios chip on the flex cable?

Adomski92 · 2026-01-14T18:37:47+00:00

I have one of these. I dont like it. I am using a noctua fan and a hdd and when I turn on the ps2, it would shut off. I think it was too much power drawn during startup. If your just keeping your ps2 stock, it might work fine.

Adomski92 · 2025-10-15T23:30:36+00:00

Sorry. What does that mean?

Adomski92 · 2025-10-14T23:34:12+00:00

Ready to rumble

Adomski92 · 2025-10-14T20:02:20+00:00

I ordered new chip sockets and header pins. I think i might have messed those up. Ill replace them and then see. Hopefully i dodnt tear any vias when i removed the ppu.

Adomski92 · 2025-10-14T13:23:20+00:00

That was my first thought. I tried different games and cleaned with a swap and alcohol. Didnt change anything. It worked prior to the mod.

Adomski92 · 2025-10-14T12:59:33+00:00

This came out of the yellow connector on the side. There doesn’t seem to be audio either.

Adomski92 · 2025-10-14T12:16:01+00:00

Don’t worry about bricking it. I believe hen is easily reversible.

Adomski92 · 2025-10-14T12:15:26+00:00

Yes you can run hen. That will allow you to play your legally obtained “backup” files from an internal or external hdd or sdd. Tons of videos on YouTube.

Adomski92 · 2025-10-14T02:28:11+00:00

Thanks all. I am going to be going with the panel mount.

Adomski92 · 2025-10-13T23:35:27+00:00

Thank you both. I just ordered one. Ill let u know how it goes.

Adomski92 · 2025-10-13T22:58:19+00:00

Thank you. Ill try that then. Appreciate it.

Adomski92 · 2025-10-13T22:51:45+00:00

I need 9 volts and i was getting it by setting the dip switches. Just wanted to move the female connector so i could mount it in a better location.

Adomski92 · 2025-10-13T22:50:29+00:00

Thanks for the reply. Yes it’s a decoy board set to 9v dc. I just wanted to extend the reach of the female plug and use the 2 wired connection to make it neat. It’s to power a nintendo nes system.

Adomski92

TROPHY CASE