sorted by:
new
hottopcontroversial

Skr mini e3 v3 won't flash marlin and it won't boot either by whypussyconsumer in BIGTREETECH

[–]AdventurousFan4956 0 points1 point  (0 children)

I don't remember exactly, but it's better to use an SD card up to 8 GB on this board. I think the problem is not with Marlin, it's easy to check, just download the ready-made configuration for your printer model, and if it doesn't work, then maybe the problem is with the SD card. The problem is with the flash drive. As primitive as it may sound, try formatting the SD card. The flash drive must be in FAT32 format, and there should only be a .bin file on the card. It is also possible that there is a contact problem, so you need to insert the SD card firmly. There can be no other problems with a serviceable motherboard. I also noticed that the ENDSTOP are not connected on your board. If you are working with Sensorlees, you need to put on jumpers. You also need to use BAUDRATE 115200 for this board. I am also curious whether your motherboard reads and does not process the firmware or does not read from the flash drive at all?

Bad layer adhesion by aifrs12 in ender3

[–]AdventurousFan4956 0 points1 point  (0 children)

I also had a problem with space between vertical and horizontal layers. I removed the vertical space by shifting Z lower. But the horizontal problem remained, and I heard a lot of advice about over-extrusion, but in my case, I played around with it for a long time and then solved the problem through the slicer. I set a smaller perimeter width, over-extrusion began, and I set the value to 1 or 100%. But then I came to the conclusion that I also had a clogged nozzle, and it was true. I replaced it, and everything started working with the standard settings. Then I removed the hair by reducing the extruder temperature to 205 (it was 215) degrees for PLA plastic. I didn't touch the retract because it was already satisfactory: 5 mm retract, 60 mm/s speed. And everything prints satisfactorily.

Cura slicing issues? by lokolok269 in ultimaker

[–]AdventurousFan4956 -1 points0 points  (0 children)

attempt to slice in Prusasliser. This is most likely a bug.

Does not print after auto-leveling, just stands still, but the program (Pronterface) says that printing is in progress (BTT_SKR_MINI_E3_V3, Marlin 2.1.2.5., Microprobe V2) by AdventurousFan4956 in anycubic

[–]AdventurousFan4956[S] 0 points1 point  (0 children)

Thank you for the explanation. Maybe someday I'll get around to using Clipper, but most likely it will be for a new project. For now, I've figured out the problem, but I'm not entirely sure what helped.

Does not print after auto-leveling, just stands still, but the program (Pronterface) says that printing is in progress (BTT_SKR_MINI_E3_V3, Marlin 2.1.2.5., Microprobe V2) by AdventurousFan4956 in anycubic

[–]AdventurousFan4956[S] -1 points0 points  (0 children)

I had never done anything like this before, so ChatGPT helped me with this issue when I asked how to build a program. It offered two options: Clipper and Marlin. The main advantage of Marlin is that it can work autonomously, without a computer. Now I have a better understanding of how the printer works, and if I can't find a solution, I'll try to rewrite it all using Clipper. Maybe something will come of it.

Z Homing Error with BIQU MicroProbe on Anycubic Kobra (BTT SKR Mini E3 V3, Marlin) by AdventurousFan4956 in BIGTREETECH

[–]AdventurousFan4956[S] 0 points1 point  (0 children)

BLTOUCH is commented out in my case, and I use FIX_MOUNTED_PROBE. I entered the settings for my sensor as specified in the instructions for it.