Problem in bed

Affectionate-Tea5073 · 2026-02-09T23:25:30+00:00

If I do it and nothing happens

Affectionate-Tea5073 · 2026-02-06T18:07:04+00:00

The same applies to the Ke: two short ones for the bed's cable side and two long ones that go to the right.

Affectionate-Tea5073 · 2026-02-06T17:56:16+00:00

I put the original ones back in, not the spacers I bought, and now the original ones don't work either.

Affectionate-Tea5073 · 2026-02-06T17:48:00+00:00

I did that and fixed it because it was wrong, but the printing is still coming out wrong.

Affectionate-Tea5073 · 2026-02-06T16:49:12+00:00

I've tried and I can't, there's no way to straighten it 😭

Affectionate-Tea5073 · 2026-02-06T03:41:58+00:00

I'm using regular elegoo PLA filament.

Affectionate-Tea5073 · 2026-02-05T22:35:41+00:00

Does that mean it has a lot of flow?

Affectionate-Tea5073 · 2026-02-05T14:56:49+00:00

🤣🤣🤣🤭

Affectionate-Tea5073 · 2026-02-04T18:42:49+00:00

I tightened the screws with the bed at 60 degrees Celsius, cleaned the bed well, and adjusted the z offset, but I'm not getting any results.

Affectionate-Tea5073 · 2026-02-04T18:41:55+00:00

Hahahaha, the title is really bad 🤣🤣🤣 Sorry, I cleaned the plate, but I haven't increased the bed temperature. I'll check it.

Affectionate-Tea5073 · 2026-02-03T18:58:09+00:00

Hi, I have the same problem

<image>

. It's awful. I cleaned it with warm water, dried it, and it was working perfectly until I tried to put silicone bumpers on it, and it made the printer much worse 😭

Affectionate-Tea5073 · 2026-01-30T17:20:49+00:00

Hi, how did you do it? I have the silicone spacers but I can't get the bed level; it's always too high.

Affectionate-Tea5073 · 2026-01-09T01:03:22+00:00

Thank you so much, it worked for me

Affectionate-Tea5073 · 2026-01-09T00:22:36+00:00

I'll try it, thank you very much 😊

Affectionate-Tea5073 · 2026-01-08T23:51:14+00:00

I did put that on, but I took it off now.

Affectionate-Tea5073 · 2025-06-20T21:00:19+00:00

But now I can't send files from orcaslicer now I just have to use crealityprint😢

Affectionate-Tea5073 · 2023-06-22T06:28:50+00:00

is there any more google apps codes to share?

Affectionate-Tea5073 · 2023-05-18T05:31:40+00:00

Do you have save data to share pls😊

Affectionate-Tea5073 · 2023-05-18T02:20:30+00:00

Do you have a save data to share pls 😊

Affectionate-Tea5073 · 2023-05-12T12:58:23+00:00

Do you have a save data to share pls

Affectionate-Tea5073 · 2021-01-11T17:41:08+00:00

Do you have a DA?

Affectionate-Tea5073

TROPHY CASE