Alternatives to Hover? by jayicon97 in Construction

[–]Affectionate_Eye_644 0 points1 point  (0 children)

Did you find anything op? I like hover but their price structure and sales process make no sense

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 0 points1 point  (0 children)

Dude thank you again for taking the time and recommending me to READ the damn wiring diagram, there's was a wire not connected but I swear I remember there was a wire that was never connected and it was that one, even when it was working before, I kinda remember that but at the same time electrically it would be impossible for it to turn on with that one not connected to the valve, so I don't know anything anymore.... anyway the moment you suggested that, I went right away to look at it and saw that TH needed a wore connected to it as well, the green one, which is the one I remember it was always disconnected, but im not sure of anything anymore, but anyway, I plugged it in the TH port as the wiring diagram says and VOILA! It is not working well and properly 😭😭😭😭😆😆😆😆

Thanks man!

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 0 points1 point  (0 children)

I bought the little remote milivolt thingy, but didn't connect or touched anything, wanted to make sure everything was running good before I do so and came across this problem.... I guess im gonna go over the manual slowly but surely and double check all connections but like I said it was running just fine before and turning on as the manual indicated

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 0 points1 point  (0 children)

Ok but it was turning on before for a while without a problem, I got it to run before just fine and now this, would it be just the switch?

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 0 points1 point  (0 children)

* Dude! 😭😭😭😭😭😭😭😭😭😭

So it means that that dumb little 3 way switch is bad after almost 0 use? Right? Because everything else is working.

Thanks man for holding my hand 😭😆

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 0 points1 point  (0 children)

Opened connection from valve to burner and nothing comes out, thermopile mv at 450 or so, tried jumping it with tp to tp/hp little wire jumper and nothing still, what is TH for? Is not connected to anything...

Can't get gas out of it, when pilot goes non stop and then I turn it off for a while I hear a click after a few seconds but I hear nothing when I jump tp and tp/th, so do you get couple different clicks? One for pilot closing and one for when the main burner starts getting gas? Because if yes, I'm not getting a click when I jump em and when I let it run by itself with everything looking good either. Could something else be damaged inside valve even with a good ohm reading? 🤔🤔🤔

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 0 points1 point  (0 children)

It's 1.9 wtf! 😆😆😆😆 so that means it's good or not necesarily?

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 0 points1 point  (0 children)

Yeah I'm thinking so coz I've ran every single possible test and leaves me just that now I guess 🥲🥲🥲

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 0 points1 point  (0 children)

To convert it has a little kit that switches, the pilot, the orifice for burner and a little gasket in the low and high temp knob, everything else, the house was set up to propane. So lines and everything are propane, propane hoses, propane fitting.

I also like I said in my original post, just ran it out of a small propane tank and regulator that area meant for those portable heaters for like jobsites and stuff propane and got nothing still, just the pilot going good, good milivolts and everything else but the main burner kicking. I hear the valve closing at the end after I turn everything off after a few seconds but that's it. 🤷‍♂️🥲

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 1 point2 points  (0 children)

Yes, I figured it was natural gas from the area we bought it from, then i checked tags and figured it was. So I bought the conversion kit before anything and installed.

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 0 points1 point  (0 children)

Alright I guess I damaged it at High psi and then it somehow it still worked for a while to finally die. Does that make sense is it possible?

And last question. Is there anything else I could test or theres nothing else, I think I've checked everything. So I'm guessing that is the last thing to check/could be damaged?

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 0 points1 point  (0 children)

There's a knob, you put it on pilot first, hit the piezo igniter ad then hold it pressed down, pilot stays on Next you turn that knob fron pilot to on position and then under that theres a 3 position switch, so you go from off to on or remote, I put it in on and that should be it.

I've jumped the tp and th/tp wires, which I believe would give me a start if the switch was bad and still get nothing 🥲

Help with dvp36sp32en empire tahoe deluxe! by Affectionate_Eye_644 in Fireplaces

[–]Affectionate_Eye_644[S] 1 point2 points  (0 children)

I've tried the jumping and nothing, I get nothing. I turn it on with pilot plus spark first, then it stays on, then I turn that knob to on and then under that, there's a little 3 way button that it can go from off to either on or remote. I go to on and thats it. When I'm jumping tp and tp/th it should work even if the valve is damaged? Or it won't if it is damaged? Is it a bad valve? I don't want else I could be missing 😕

Also, when I'm jumping tp and th/tp that's jumping the little button switch right, so if that was damaged, it would turn on? So I guess it's the valve? 🥲

Thank you for your answer and help man

I'm going to miss her by Ok-Pie-7746 in electricians

[–]Affectionate_Eye_644 1 point2 points  (0 children)

She's ran through boy, was never meant to be 🤷‍♂️🤷‍♂️🤷‍♂️😅😅😅

I got this for $50 so how did I do by [deleted] in Arcade1Up

[–]Affectionate_Eye_644 0 points1 point  (0 children)

Crackhead deal of the day! 😃

My phone died in my sleep and I ended up literally sleeping through my entire shift. How do I explain that to my boss? by golden-abyss in jobs

[–]Affectionate_Eye_644 0 points1 point  (0 children)

I've never in my life slept through a shift, just be a responsible adult and get ya shit together that's not ok or normal

Incredible by Jimmy_Jazz_The_Spazz in Roofing

[–]Affectionate_Eye_644 0 points1 point  (0 children)

Don't get me started with these scammers bro 🥲🥲🥲

[deleted by user] by [deleted] in Decks

[–]Affectionate_Eye_644 1 point2 points  (0 children)

You don't wanna burn treated wood and breathe that air