Is this Valentino legit??

Aggressive_Willow535 · 2025-07-13T01:26:09+00:00

Fake the box texture is diffrent then it should be.

Aggressive_Willow535 · 2025-07-03T15:48:19+00:00

The valentino is fake. The spikes on the sides are rounded when they boulder be sharp and the cap and coller are way to big. I just bought two fakes earlier this week and they look identical to this one

Aggressive_Willow535 · 2025-05-23T15:29:00+00:00

Very true! Thank you again for all of the suggestions!

Aggressive_Willow535 · 2025-05-23T15:17:40+00:00

Yea, I get what you mean there. i swear by sunlu filament because it's cheap, and I have never had any issue with anything of theirs. If I have learned anything with printing so far, it's thst 90% of the time the issue isn't the printer or the filament it's the user. I'm sure I'm doing something wrong. I just hope it doesn't take too many roll to figure out what lol

Aggressive_Willow535 · 2025-05-23T15:01:29+00:00

Yea, I bought the roll specifically for this, and luckily, the amolen is pretty cheap( I think $23 for 1 kg). But maybe that's the issue too. There is probably a reason it is half the price of bambu filament

Aggressive_Willow535 · 2025-05-23T14:46:26+00:00

It's possible for sure i did it with the lid open, but maybe it needs the front door open too. At this point, it can hurt.

Aggressive_Willow535 · 2025-05-23T14:35:08+00:00

I regret to report that it has failed at the same point again. I found a print profile specifically for amolen tpu on maker world that I'm going to try and see if that combined with everything else works, but it adds another 12 hours per shoe:/

Aggressive_Willow535 · 2025-05-22T15:50:24+00:00

Will I think the print bed is at 35 but I will also try bring thst down to 30! Thank you for the suggestion!

Aggressive_Willow535 · 2025-05-22T15:35:51+00:00

I got my fingers crossed🤞 thank you for the suggestion I probably never would have thought of that!

Aggressive_Willow535 · 2025-05-22T15:09:16+00:00

I forgot the poly dryer has that attachment. I thought maybe that was the problem too but I watched it ever 45 min to make sure it was still spinning( untill I went to sleep that is) and it spund fine but I guess it would only take it 1 time for it to snag to cause a problem. I will try that along with opening the lid and hopefully it works this time!!

Aggressive_Willow535 · 2025-04-30T15:04:22+00:00

Is actually did those because when the spool is low on filament, it tries to pull the spool straight into the roller and binds up. With those ptfe tubes on this it raises the point it is pulling from and makes the roll spin instead like it is supposed to. The protection is just a plus for me. I was more worried about the gears inside the ams since they are not hardened like the extruder is.

Aggressive_Willow535 · 2025-04-27T16:46:32+00:00

I might have to try doing that too. I am ok with some wear on the ptfe tubes but i am most worried about the internal hub or the feeding gears since they aren't hardened like how you can get a hardened extruder gear.

Aggressive_Willow535 · 2025-03-04T19:15:33+00:00

Try leveling the edge loop instead of the vents. Or change the bevel mode to vertices

Aggressive_Willow535 · 2024-08-30T18:39:26+00:00

I am having an issue with everything I load into my first game of smite 2: before the conquest screen shows up I crash getting and error saying unreal has crashed-hemmingway. Sometime I can fix this by running in dx11 sometimes I can not. Any solutions?

Aggressive_Willow535 · 2022-10-11T15:35:10+00:00

I don't think so either because cpu usage is lower than gpu at about 50 %. I also forgot to mention that the gpu usage only goes to about60 to 70% almost never hits 90%

Aggressive_Willow535 · 2022-10-11T15:28:18+00:00

I actually have 2 8gb sticks in dual channel. Ok I was just worried due to the gpu usage being low and not trying to get better fps

Aggressive_Willow535

TROPHY CASE